Yes: a building can flush its toilets and urinals with water from its own showers, bathtubs and bathroom sinks, as long as that greywater is collected in separate drains, treated, disinfected and delivered through separate, labeled piping. The International Code Council’s guide to the 2018 International Plumbing Code says greywater used for flushing must be treated by an onsite system that complies with NSF/ANSI 350 and must not be stored for more than 24 hours. A working system also needs city water makeup protected against backflow, an overflow and bypass to the sewer, and people who maintain it on a schedule.
This article follows that loop from the drain to the bowl: what counts as greywater, how treatment works, how long water can sit, how supply compares with flushing demand, and what tends to fail. Code text is covered in what the plumbing code requires for reuse systems, and the money question in when greywater recycling pays for itself.
What counts as greywater, and what does not
Greywater is used water from showers, bathtubs, bathroom sinks and, in some systems, clothes washers. It never includes toilet or urinal waste, and federal definitions also leave out kitchen sinks.
EPA’s WaterSense at Work guide defines gray water as “wastewater from lavatory sinks, laundries, and bathing.” It adds that gray water “never contains wastewater from toilets or urinals and excludes wastewater from kitchen sinks.” The Department of Energy’s Federal Energy Management Program (FEMP) uses almost the same line in its alternative water guidance: greywater comes from bathroom sinks, showers and clothes washers, and does not include wastewater from toilets, urinals or kitchens.
Toilet and urinal waste is what people usually mean by blackwater. The difference is not a matter of wording. The Water Research Foundation’s guidance for onsite systems sets much higher pathogen reduction targets for blackwater than for greywater, because blackwater carries fecal contamination as a matter of course.
| Drain | Greywater? | What it brings to a treatment system |
|---|---|---|
| Showers and bathtubs | Yes | The largest, steadiest flow in homes, apartments and hotels; soap, hair, skin and body oils |
| Bathroom sinks | Yes | A small flow; soap, toothpaste and shaving residue |
| Clothes washers | Yes in EPA and DOE definitions, if the system is rated for laundry | Lint and detergent; a heavier load than shower water |
| Kitchen sinks and dishwashers | No | Food, grease and a much higher organic load |
| Toilets and urinals | No (blackwater) | Fecal contamination and far higher treatment targets |
| Roof rain, AC condensate, cooling tower blowdown | No (separate onsite sources) | Different quality, different treatment |
Light and heavier greywater
Not all greywater is equal. A 2025 comparative study in Frontiers in Environmental Science notes that water from showers and bathtubs is generally not very polluted, that washing machines tend to carry a higher pollutant load, and that kitchen water is higher still. Portugal’s technical specification, which the study follows, gives priority to “light greywater” from baths, showers and sinks.
Laundry is a choice the designer makes, not a default. EPA explains that NSF/ANSI 350 greywater systems “can be evaluated for treating bathing water only, laundry water only, or both.” In a hotel with an on-premise laundry, rinse water can instead feed a separate laundry recycling loop, and the greywater calculator lets you enter zero laundry water for that case.
How a greywater toilet-flushing system works, step by step
A building-scale system runs greywater through seven steps: separate collection, screening, short holding, treatment, disinfection, treated storage with a disinfectant residual, and delivery through purple pipe. City water makeup and a bypass to the sewer sit at the edges of the loop.
- Separate drains. Shower, tub and lavatory drains run to their own stack instead of the building sewer. FEMP notes that a greywater system “requires retrofitting the plumbing system for existing buildings” and is easier to build into new construction.
- Screening. A screen or self-cleaning filter takes out hair, lint and grit. Valley Water, the Santa Clara County water district, warns that even fairly clean greywater has “particles, lint, hair, etc.”, so filters must be maintained.
- Collection tank. Showers come in morning and evening bursts, while toilets flush all day. The Water Research Foundation’s 2020 guidance manual explains that holding tanks even out these swings so treatment runs at a steady rate. This tank holds water for hours, not days.
- Treatment. Most building systems use biological treatment, where aerated bacteria break down soap and skin residue, followed by a membrane. A UK Environment Agency report describes a common four-stage setup: settling, aerobic treatment, membrane filtration and treated water storage.
- Disinfection. EPA recommends disinfection “for all water used indoors for toilet flushing or other uses.” In the foundation’s example greywater train, a membrane bioreactor feeds a UV reactor designed for 150 millijoules per square centimeter.
- Treated storage with a residual. UV leaves nothing in the water, so a small chlorine dose keeps bacteria from regrowing in the stored water and the pipes.
- Delivery. A booster pump sends treated water through dedicated, labeled piping to toilets and urinals only.
Short retention units are a different thing
Some products for homes and hotel rooms skip most of these steps. The UK Environment Agency describes “short retention” units that collect shower water near the toilet, let particles settle and skim the surface, and flush unused greywater out with mains water after a set time. They are small and simple.
Whether a given unit is acceptable in a given building is a question for the local code official, because the 2018 code text ICC summarizes ties flushing systems to NSF/ANSI 350.
How clean the water has to be before it reaches a toilet
No single national number applies everywhere. The 2018 code points to NSF/ANSI 350 for treatment units, and the Water Research Foundation’s guidance gives pathogen reduction targets that a treatment train must add up to. Your local authority decides which of these it applies.
NSF/ANSI 350 and its two classes
NSF/ANSI 350, “Onsite Residential and Commercial Water Reuse Treatment,” sets what EPA calls the “minimum materials, design and construction, and performance requirements” for onsite reuse treatment systems. NSF’s public listing uses two classes. Class R covers single-family residential dwellings. Class C covers multifamily residential units and commercial facilities.
| Manufacturer as listed | Greywater models listed | Rated capacity, gallons per day | Class |
|---|---|---|---|
| Dehoust GmbH (Germany) | GWtec 140 to 640 (6 models) | 1,321 to 7,926 | C |
| INTEWA (Germany) | AQUALOOP GW300 to GW5400 (8 models) | 79 to 1,427 | C |
| Hydraloop International (Netherlands) | H350/H300 and H600 (2 models) | 52.8 and 260 | R |
On that date the listing named 6 manufacturers and 69 products, and only three manufacturers listed greywater systems. Two practical points follow.
First, the class matters: an apartment building or hotel needs a Class C listing, not a unit tested for one house. Second, the rated capacity in gallons per day has to cover the building’s daily greywater flow, so the size of the building narrows the choice quickly. Maredes specifies a unit listed under NSF/ANSI 350 in the class that fits the building where the market offers one, and checks the listing rather than the brochure.
Pathogen reduction targets
The Water Research Foundation’s Onsite Non-Potable Water System Guidance Manual (2020), which EPA lists among its key onsite reuse resources, expresses treatment as log reduction targets. One log means a 90 percent reduction, two logs 99 percent, three logs 99.9 percent, and so on. The targets aim at a risk benchmark of 1 infection per 10,000 people per year.
| Source water and use | Enteric viruses | Parasitic protozoa | Enteric bacteria |
|---|---|---|---|
| Greywater, indoor use such as toilet flushing | 6.0 | 4.5 | 3.5 |
| Greywater, unrestricted irrigation | 5.5 | 4.5 | 3.5 |
| Blackwater or mixed wastewater, indoor use | 8.5 | 7.0 | 6.0 |
| Roof runoff, indoor use | Not applicable | No data | 3.5 |
The manual’s example greywater train meets these targets with a membrane bioreactor and a UV reactor designed for 150 millijoules per square centimeter, which it credits with 6 logs for all three pathogen groups. It adds that a disinfectant residual is still needed to keep the water stable in the pipes. For the pipes themselves, the manual gives sample goals: biochemical oxygen demand and suspended solids each below 10 mg/L on a four-week average, no offensive odor, and 0.2 mg/L of free chlorine (or 0.5 mg/L of combined chlorine) at or near the point of use.
Questions to put to any treatment unit
A brochure that says “certified” is not enough. Before a unit goes into a specification, get written answers to these:
- Is the model on the current NSF/ANSI 350 listing, and in which class, R or C?
- What rated capacity in gallons per day does the listing show, and does it exceed the building’s daily greywater flow with room to spare?
- Was it evaluated for bathing water, laundry water or both, and which will the building send it?
- Does the package include UV, a chlorine residual, or both, and who supplies the dosing equipment?
- Which readings are continuous, which alarms exist, and what happens automatically when a critical alarm trips?
- What are the service intervals for screens, membranes and lamps, and who can do the work locally?
How long greywater can be stored, and why it starts to smell
Greywater should be treated or used within about a day. ICC’s guide to the 2018 code says greywater “cannot be stored untreated in excess of 24 hours,” and EPA says treated gray water “should always be used within 24 hours of collection, or otherwise properly disposed.”
The reason is biology. EPA’s treatment table calls greywater “biologically unstable for long periods of storage unless treated.” The 2025 Frontiers study explains that the soaps, skin and hair in greywater are easily biodegradable, so treatment “cannot be delayed too much” before decomposition involving sulphates produces unpleasant smells.
Temperature works against you too. The UK Environment Agency report says storing water “in a cold dark environment reduces the rate of deterioration,” and the Water Research Foundation lists temperature control among its distribution practices. A tank in a hot mechanical room or a sunny service yard in a Gulf South summer has neither advantage, so tank placement deserves as much thought as tank size.
How big the tanks should be
Smaller is usually better for greywater. The site’s greywater calculator reports storage for one day of flushing demand, and the tank sizing calculator notes that for daily flows like greywater, “a day or less of storage keeps water fresh.” The Portuguese specification described in the Frontiers study makes the same point: the greywater tank should stay close to the volume used each day.
Sizing tanks around the building’s daily rhythm
Greywater and flushing do not happen at the same hours. The Water Research Foundation’s manual gives a simple case: if 10,000 gallons of source water arrive over 12 hours a day and the building uses water evenly around the clock, about 5,000 gallons of storage cover the hours with no inflow. Spread the same 10,000 gallons over 18 hours and the storage needed falls to 2,500 gallons.
Most residential buildings look like the first case. Showers cluster in the morning and evening, while toilets flush through the day and into the night.
The usual answer is two modest tanks instead of one large one: a collection tank that absorbs shower peaks so treatment runs at a steady rate, and a treated tank that absorbs flushing peaks so toilets do not fall back on city water every morning. Both stay within the one-day limit. In the calculator’s default example below, one day of flushing demand is 858 gallons, which sets the scale for the treated tank.
Quiet periods need a plan. The Water Research Foundation warns that commercial buildings “may have little to no water usage over weekends and holidays.” A hotel at low occupancy or a dormitory over a holiday break faces the same problem. The control system should drain or bypass stale water to the sewer, run toilets on city water, and flush the lines before the building fills again.
Matching greywater supply to flushing demand
Compare the greywater a building makes each day with the water its toilets use. In buildings where people shower daily, supply usually exceeds flushing demand; in offices without showers, it rarely does.
The greywater calculator uses two lines of arithmetic:
- Supply = people × (shower and bath + bathroom sink + laundry, if collected) × (1 − treatment loss)
- Flushing demand = people × flushes per person × gallons per flush
The water you can reuse is the smaller of the two. Anything above demand overflows to the sewer, or, where the local code allows it, goes to subsurface irrigation: ICC notes that untreated greywater may be discharged to a subsurface landscape irrigation system under the code’s Chapter 14.
The calculator’s default example
The calculator opens with the fictional Pearlbank Hotel at 70 percent occupancy, about 134 guests, with planning assumptions of 16 gallons of shower and bath water and 3 gallons of bathroom sink water per guest, no laundry water, 5 flushes a day at 1.28 gallons per flush, and a 10 percent treatment loss. Its results:
- Greywater collected and treated per day: 2,291 gallons
- Toilet flushing demand per day: 858 gallons
- Share of flushing greywater can cover: 100 percent
- Greywater left over per day: 1,434 gallons
- City water saved per year: 313,024 gallons
- Storage for one day of flushing demand: 858 gallons
Supply is more than two and a half times demand. Even so, the fictional hotel’s water review screened greywater flushing and did not choose it, because the existing building has no separate drain and supply piping.
The example project walks through that decision. The lesson is that supply is rarely the limit in a building with showers; plumbing, treatment and upkeep are.
Example (fictional). The Bayhollow Apartments is a 72-unit building with about 130 residents and older 1.6-gallon-per-flush toilets. The planning assumptions are 14 gallons of shower and bath water and 3 gallons of bathroom sink water per resident per day, laundry not collected, 5 flushes a day, and a 10 percent treatment loss. The greywater calculator gives 1,989 gallons of treated greywater a day against 1,040 gallons of flushing demand, so greywater covers all flushing and 949 gallons a day go to the sewer.
City water saved would be 379,600 gallons a year.
Now replace the toilets first. At 1.28 gallons per flush, flushing demand drops to 832 gallons a day, and the greywater system would save 303,680 gallons a year. The toilet swap alone removes 208 gallons a day, about 75,920 gallons a year, with no treatment plant at all.
Every number here is a planning assumption for a fictional building.
That sequence follows public advice. EPA WaterSense says toilets account for “nearly 30 percent of an average home’s indoor water consumption” and that labeled models use 1.28 gallons per flush or less, 20 percent less than the 1.6-gallon federal standard. Valley Water puts it plainly: “In general, it’s more cost-effective and sustainable to replace your toilets with the most-efficient toilets on the market.”
When greywater falls short
For example, suppose a hypothetical office has 200 workers, no showers, 1 gallon of bathroom sink water per person per day and 3 flushes per person at 1.28 gallons. The calculator gives 180 gallons of greywater against 768 gallons of flushing demand, covering 23 percent and leaving 588 gallons a day to city water. The UK Environment Agency report reaches the same conclusion in words: low-level treatment systems such as short retention units are “less applicable in buildings such as offices that have lower yields of greywater.”
Makeup water, overflow and backflow protection
Every greywater system needs city water to fill the gap when greywater runs short, and that connection is where drinking water is most at risk. The makeup line enters through an air gap or a reduced pressure backflow assembly, and tanks overflow to the sanitary sewer.
ICC’s code essentials for the 2018 code say makeup and backup connections from the potable system “must be protected in accordance with IPC Section 608.” It calls a physical air gap “the best protection,” and says that if a physical connection is necessary, a reduced pressure principle backflow prevention assembly “would be the appropriate method of protection.” Storage tanks must be identified as nonpotable, and outlets and piping are signed and labeled.
FEMP lists what local rules may add: inspection after installation, “extensive labeling, different piping material, and biodegradable dye to distinguish from the building’s potable system,” and backflow preventers. In a toilet bowl, dye also makes it obvious to anyone that the water is not from the drinking supply.
Labels a maintenance worker should be able to read
The point of labeling is that a plumber who has never seen the building can tell which pipe is which. FEMP says dual plumbing should be color coded and that reclaimed water pipes “must be color coded with purple tags or tape according to standards set by the American Water Works Association.” In practice that means purple pipe or purple tape and tags along every treated greywater line, a “non-potable” label on each tank, and signs at every fixture the system serves.
Treated greywater should never connect to a sink, shower, drinking fountain or ice machine. During renovations, the as-built drawings and labels are the only defense against a contractor tying a new sink into the wrong riser.
The bypass matters as much as the makeup
When treatment fails, the system should stop sending water to toilets. The Water Research Foundation’s sample alarm table shows how: a critical reading, such as filter effluent turbidity reaching 0.5 NTU or UV transmittance falling to 75 percent, triggers “automated diversion to sewer.” Toilets then run on city water until someone fixes the fault.
That design has a known weakness. The UK report cites a study that found systems which had failed and “switched to mains back-up with users unaware of the failure.” A bypass keeps toilets working, so nobody notices. The alarm therefore has to reach a person: a text to the maintenance lead, a light on a panel someone checks, or a line in a monitoring report.
Which buildings suit greywater toilet flushing
Greywater flushing fits buildings with many showers, many toilets, steady occupancy and someone on staff to look after it. It fits poorly in offices, single homes and existing buildings whose drains cannot be separated.
Valley Water says greywater for toilet flushing “is more appropriate in commercial or other high-density properties where dedicated staff can maintain it over time.” FEMP adds that dual plumbing “can be integrated into the design with less labor” in new construction than in a retrofit. The Frontiers study adds a caution for collective buildings such as student residences and hotels, where health risks and testing burdens are higher.
| Building | Greywater supply | Flushing demand | Fit |
|---|---|---|---|
| New apartment building or dormitory | Daily showers in every unit | Steady, mornings and evenings | Strong candidate if separate drains are designed in from the start |
| Existing apartment building | Same | Same | Depends on whether stacks can be separated; replace old toilets first |
| Hotel | Guest showers that follow occupancy | Guest rooms and public restrooms | Good supply; occupancy swings and guest reaction to color or odor matter |
| Office | Bathroom sinks only, unless there are showers | High on workdays, near zero on weekends | Weak: supply often below demand |
| Single-family home | One household | Small | Class R units exist, but efficient toilets usually come first |
| Restaurant | Kitchen water is excluded | Restrooms | Weak |
For apartment owners, the apartments page explains how a review starts with the master meter and the toilets before reuse. Hotel owners can read what hotels that recycle greywater had to manage, from occupancy swings to guest complaints.
What about a bucket, or a sink on the toilet tank?
The simplest greywater flush is manual: a bucket of collected shower water poured into the bowl. It needs no plumbing, but it is a household habit, not a building system. Valley Water also notes that toilets that reuse water from a sink mounted directly above the tank are on the market.
The Frontiers study calls this the “direct level” of reuse in a bathroom, a washbasin combined with a flush toilet. Neither approach changes the picture for an apartment building or hotel, where water has to be treated, stored and delivered to dozens or hundreds of toilets every day.
Why staff time decides the fit
A greywater system is a small treatment plant inside the building. The Water Research Foundation notes that onsite systems are rarely staffed full time and are “more often operated remotely.” Someone still has to clean screens, change lamps and respond to alarms. A building without that person is a poor fit at any size.
What goes wrong: odor, color, clogged filters and silent failures
Most problems trace back to four causes: water held too long, filters that are not cleaned, disinfection that runs out, and failures nobody notices. The UK Environment Agency’s review of domestic greywater systems reported each of them.
The UK report, published in 2010, summarizes an earlier agency study of greywater systems. That study found “variable reliability of the systems,” filters that “required regular cleaning to avoid blockages,” and “odour problems due to either poor water quality or high levels of disinfectant.” In another study the report cites, more than half of individual systems failed, and the most common fault was insufficient water flow to flush the toilet.
Parts wear on a schedule. The report puts pump life “in the region of 10 years” and says UV bulbs and some membranes need replacing every one or two years.
It also warns that biological systems are “vulnerable to contamination by chemicals,” so residents need to know what not to pour down a shower drain. Valley Water adds that toilet-flushing systems “usually require frequent maintenance, manual cleaning of filters, and chemical disinfectant to prevent odors in the bathroom.”
| What you notice | Likely cause | First check |
|---|---|---|
| Musty or rotten-egg odor at toilets | Water held too long, or the chlorine residual has run out | Residual at the farthest toilet; tank level and age of the water |
| Gray, yellow or cloudy water in the bowl | Treatment upset, a fouled membrane or a filter bypass | Turbidity reading; membrane pressure; bypass valve position |
| Strong chlorine smell | Overdosing after a residual alarm | Dosing pump setpoint |
| Toilets slow to refill | A clogged screen, a pump fault or a stuck makeup valve | Screen, pump pressure, makeup float |
| Water bill unchanged for months | Silent bypass to city water | Meter on the treated line; alarm history |
| Treatment struggles after a deep clean | Bleach or drain cleaner sent down greywater drains | Ask staff and residents; check the biological stage |
Hotel owners should add one more line: guests are likely to notice color and smell before any lab result arrives. The foundation’s manual makes the same point about the public, noting that water that is “turbid, off-colored, or malodorous may lead to public opposition even if the water is demonstrably safe.”
Maintenance and monitoring the building has to commit to
A greywater system needs a written maintenance schedule, continuous readings on the steps that control pathogens, and any sampling the local authority sets. Budget staff time and testing before buying equipment.
Start-up comes before the first flush
The Water Research Foundation’s manual separates start-up from commissioning. Start-up is when equipment is brought online, calibrated and checked, and when the biological stage is given time to acclimate.
Commissioning is when the whole system is tested against the design. Regulators may ask to see the alarms, diversion and shutdown features work, and to inspect the building for cross-connections and backflow devices, before treated water reaches a toilet.
A useful start-up record has four parts: the date each component came online; baseline readings for turbidity, chlorine residual and UV transmittance; a test of each critical alarm and its automatic diversion; and the first laboratory results set against whatever limits the local authority applies. Maredes calls this stage start-up and verification, and its report becomes the baseline that later service visits are compared with.
The routine after start-up
FEMP’s list for a regular greywater maintenance program is short and specific:
- Inspect the system for leaks and blockages.
- Clean and replace the filter.
- Replace the disinfectant.
- Make sure controls operate properly.
- Periodically flush the entire system.
The Water Research Foundation adds the monitoring layer. It favors online readings of stand-in measures, such as chlorine residual with contact time, turbidity after filtration and UV transmittance, over occasional effluent samples. It recommends that treatment meet its targets “no less than 95% of the time,” which only continuous readings can show.
Testing has a cost that owners tend to miss. The Frontiers study says the need for analytical control is “often ignored or undervalued.” In its Portuguese single-family example, the required tests cost no less than 1,200 euros a year while the household’s whole mains water bill did not exceed 500 euros.
Buildings with many units spread that cost, which is one reason greywater suits larger buildings better than single homes. ICC’s guide notes the local jurisdiction “may require initial testing or ongoing testing and monitoring.”
Running costs to plan for
A greywater system uses power every day it runs. The Frontiers study puts the energy for greywater treatment at around 1.8 kilowatt-hours per cubic meter, which is about 6.8 kilowatt-hours per 1,000 gallons, and notes that rainwater for the same uses needs no treatment energy in its example. The UK Environment Agency found the operational energy and carbon intensity of most greywater systems more than 100 percent higher than mains water, with short retention systems the exception at about 40 percent lower.
Those are Portuguese and British conditions, but the direction carries over: blowers, pumps and UV lamps run on electricity.
Consumables and labor come next: UV lamps and some membranes every one or two years, a pump in about a decade, disinfectant, screens, laboratory fees and the hours of the person who keeps the log. Put all of them in the operating cost line of the water savings calculator before you trust any payback figure.
Add the reuse system to the water management program
Stored, lukewarm water in a building is a Legionella question. The foundation’s manual names Legionella as a pathogen “that can grow in plumbing and be aerosolized during toilet flushing.” Reuse tanks, treated water lines and the bypass belong on the building’s water management program diagram; the Legionella checklist is a place to start. Maredes includes a monitoring and service plan with a maintenance log after any system it designs.
Who approves a greywater system in Mississippi
Approval is local and project by project. EPA’s list of 12 states with onsite non-potable reuse regulations or guidelines does not include Mississippi, so the local building official, and where wastewater is involved the health department, decides what is allowed.
EPA’s onsite reuse resource page, updated June 26, 2026, lists California, Colorado, Florida, Georgia, Hawai’i, Minnesota, New Mexico, Ohio, Oklahoma, Oregon, Texas and Wisconsin. ICC’s guide is direct about the gap between code text and local practice: “even though these systems are addressed in the code, they may not be approved for use locally.” EPA’s guidance also says to “consult local health department officials first.”
This article describes public sources; it is not legal or engineering advice, and local rules apply. For the code requirements in detail, see greywater and plumbing codes. In every reuse design, Maredes writes a code path memo that records who approves the system, which code edition applies, and the backflow, labeling and monitoring requirements.
Before you plan one: a short checklist
Most of the decision can be made on paper before anyone prices equipment. Work through these steps in order.
- Read the meter and the bills. Twelve months of water and sewer bills show the baseline. In Jackson, JXN Water bills water and sewer from water meter readings, so every gallon of flush water replaced comes off both charges.
- Fix and replace first. Repair running toilets and price efficient toilets before reuse. The Bayhollow example shows how much a toilet swap does on its own.
- Estimate supply and demand. Use the greywater calculator with your own occupancy and fixtures, and the water use calculator to check the total against the bills.
- Check the plumbing. Find out whether shower and lavatory drains can be separated from toilet and kitchen drains, and where a supply riser for treated water could run. In an existing building this step often decides the answer.
- Find the space. A collection tank, treatment skid and treated tank need a cool room with a floor drain, power and access for service.
- Pick the class and size. A multifamily or commercial building needs a Class C listing with a rated capacity above its daily greywater flow.
- Name the person. Decide who cleans screens, reads alarms and keeps the log before the system is built.
- Ask the local official early. Bring a one-page description to the building department and, where wastewater is involved, the health department.
If the numbers and the plumbing look promising, the greywater recycling service and the how it works page describe how Maredes, a Jackson, Mississippi company that designs compact water treatment and reuse systems for one building at a time, approaches the design. A project starts with a water review, and you can describe your building to begin. More articles on reuse sources are in the water reuse section.
