Maredes homeRequest a water review
Menu

Is greywater recycling worth it? Costs, payback and building size

The reader questionWhen does a greywater recycling system pay for itself, and when does it not?

A small wooden abacus stands upright at the waterline, its upper rows of plain beads dry in the air and its lower rows under the surface, some beads slid to one side.

Greywater recycling pays for itself only where many people flush toilets every day, the building pays a high combined water and sewer rate on its last gallons, and separate drain and supply piping can go in without opening every wall. A single-family home almost never qualifies: with 1.28-gallon toilets the savings are capped at about 2,336 gallons per person a year, worth about $93 a year in water and sewer charges for a family of four in Jackson, so a $3,000 system would take about 62 years to pay back under the Alliance for Water Efficiency’s operating cost assumptions. Apartment buildings, dormitories and hotels with steady occupancy and new or fully renovated plumbing are where the arithmetic can work, and even there operating cost, testing and piping decide it.

This article works through that arithmetic with published numbers only. Maredes has no installed systems and publishes no prices, so every cost below comes from a cited source or is labeled as a hypothetical example. The method is the one used by the site’s water savings calculator, and the gallons come from the greywater calculator.

How to tell whether greywater recycling pays: the four numbers

Payback depends on four numbers: the gallons of city water the system actually replaces, the rate you pay for those gallons, the yearly cost of running the system, and the installed cost. Multiply the gallons by the rate, subtract the operating cost, and divide the installed cost by what is left. That result, in years, is the simple payback.

The Alliance for Water Efficiency (AWE), in its 2017 report on single-family greywater systems, uses the same sequence. Net annual savings equal “the annual volume of potable water savings multiplied by the marginal volumetric rate for water (or water & wastewater) minus any operations and maintenance (O&M) costs,” and simple payback equals “the total installed cost of the system divided by the average annual net cost savings” (AWE, 2017). AWE adds the test that matters most: “If the payback period exceeds the expected life span of the graywater system, the system will have a net cost to the customer.”

Gallons replaced, not gallons collected

The first number is the one most often overstated. AWE puts it plainly: “The volume of water savings is not equal to the volume of graywater collected. The volume of water savings is equal to the reduction in potable water demands.” A building may produce thousands of gallons of shower water a day, but if the toilets only flush 600 gallons, 600 is the number that goes on the bill.

The greywater calculator follows the same rule. It compares greywater supply (people times shower, sink and laundry gallons, minus treatment losses) with flushing demand (people times flushes times gallons per flush) and counts only the smaller of the two as city water saved.

The rate on your last gallons

The second number is the marginal rate: what you pay for the last gallons on the bill, not your average cost per gallon. AWE says to use “only the volumetric cost of water and/or sewer,” and to leave out fixed fees such as meter charges. Where sewer is billed on water meter readings, as it is in Jackson, the sewer charge is part of the rate. The next chapter looks at Jackson’s numbers in detail.

Operating cost

The third number covers electricity for pumps and treatment, filters and membranes, disinfection supplies, laboratory testing, backflow device testing, permits where required, service visits and staff time. AWE’s single-family assumptions are small: about $1 per 1,000 gallons treated for chemicals and energy, citing a National Academy of Sciences report, plus a minimum of $36 a year for maintenance. For buildings that need regular water quality testing, the figure is much larger, as the chapter on costs people leave out shows.

Installed cost and how long the equipment lasts

The fourth number comes from contractor bids for a specific building, and it has to be compared with the life of the equipment. AWE’s worked example uses a $3,000 system (converted from an Australian consumer guide’s price of $4,000 Australian) with a 15-year life taken from a Los Angeles cost-benefit study. A 2025 Portuguese study in Frontiers in Environmental Science gives the main components of a greywater system a useful life of 15 to 20 years, against 40 to 50 years for a rainwater system (Pimentel-Rodrigues and Silva-Afonso, 2025). A payback longer than about 15 to 20 years therefore means the equipment wears out before it has paid for itself.

What simple payback leaves out

Simple payback is a screening number. The water savings calculator’s note says it “ignores financing and price changes and is not a promise of savings.” Rate increases make reuse look better over time; JXN Water’s March 2026 adjustment raised residential bills by about 11.7 percent. Interest on borrowed money, replacement parts in later years and the time value of money make it look worse.

The EPA-led study discussed below used a 30-year net present value with a 5 percent real discount rate instead, which counts a dollar saved in year 20 as worth much less than a dollar spent today. If simple payback already exceeds the equipment’s life, a discounted analysis will not rescue the project. If simple payback is short, a discounted analysis is worth doing before you commit.

Why toilet flushing caps the savings

In most buildings, greywater supply is larger than toilet demand, so the toilets set the ceiling. AWE reports that an average home “produces almost twice as much shower-based graywater than would be required for toilet flushing (assuming the use of WaterSense-labeled toilets),” which means “the potential for potable water savings is related to the volume of water used for toilet flushing and not to the volume of graywater generated by showering.”

AWE’s numbers come from the Water Research Foundation’s 2016 study of residential water use: about 10.6 gallons of shower water per person per day and about five flushes per person per day. At 1.28 gallons per flush, five flushes use 6.4 gallons a day, or 2,336 gallons per person per year. That is the most a shower-to-toilet system can save per person, before any treatment losses or downtime. AWE notes that two field studies it reviewed observed lower savings than this theoretical figure.

Toilet efficiency moves the ceiling. EPA WaterSense says toilets account for “nearly 30 percent of an average home’s indoor water consumption,” the federal standard is 1.6 gallons per flush, WaterSense labeled toilets use 1.28 gallons or less, and older toilets can use “as much as 6 gallons per flush” (EPA WaterSense, Residential toilets). Replacing old toilets with labeled models, EPA says, can cut the water a family uses for toilets by 20 to 60 percent, “nearly 13,000 gallons of water savings for your home every year.”

That creates an order of operations. Efficient toilets cut the same demand that greywater would supply, at a fraction of the complexity, and they shrink the greywater opportunity that remains. In the greywater calculator, 96 residents flushing five times a day need 768 gallons a day at 1.6 gallons per flush but 614 gallons at 1.28, so the efficient toilet alone takes about 56,000 gallons a year off the table greywater would have served. In a building with old toilets, replace the toilets first; then run the greywater numbers on what is left. The Portuguese study makes the same point: installing efficient devices “must always be the priority technical measure,” with greywater and rainwater as complementary measures.

Example (fictional). A fictional household of four in Jackson enters its numbers in the greywater calculator: 10.6 gallons of shower water per person per day (AWE’s average), nothing from sinks or laundry, five flushes a day at 1.28 gallons, and 10 percent lost in treatment. The calculator shows 38 gallons of greywater collected and treated per day against 26 gallons of flushing demand, so greywater covers 100 percent of flushing, 13 gallons a day are left over, and city water saved is 9,344 gallons a year. The extra shower water does not count toward savings.

When supply runs short instead

The ceiling flips in buildings with few showers. Offices, schools, shops and restaurants flush many toilets but produce little greywater: they have few showers, bathroom sinks add little volume (AWE leaves lavatory water out of its estimates as “minimal”), and kitchen sinks are excluded. EPA defines gray water as “wastewater from lavatory sinks, laundries, and bathing” that “excludes wastewater from kitchen sinks.” Enter zero shower water in the greywater calculator and the share of flushing that greywater can cover drops sharply, so the system saves only what the bathroom sinks supply. For those buildings, rainwater or air-conditioning condensate is usually the better source to screen.

What Jackson’s water and sewer rates do to payback

The rate is the lever owners most often underestimate. JXN Water bills water and sewer together on metered use: “Water and sewer services are based on water meter readings. All customers pay the same rate for water and sewer services based on how much water they use” (JXN Water, Rates). Since March 23, 2026, the combined rate has risen by block, so a building that uses more pays more for its last gallons.

Monthly use blockCombined water and sewer, per CCFCombined, per 1,000 gallonsWater-only, sewer-only or irrigation-only, per CCFSame, per 1,000 gallons
0 to 50 CCF$7.48$10.00$3.74$5.00
51 to 150 CCF$14.96$20.00$7.48$10.00
151 to 350 CCF$17.45$23.33$8.73$11.67
351 CCF and above$19.95$26.67$9.98$13.34
Source: JXN Water, Rates, court-approved adjustment effective March 23, 2026 (page modified July 27, 2026), checked November 2026. 1 CCF = 748 gallons; per-1,000-gallon figures are our arithmetic. The monthly availability charge per meter (for example $40 for a 5/8-inch meter) is fixed and is not reduced by reuse.

Four points follow from the rate table:

  • Sewer doubles the value of a gallon. On a combined account, the charge per 1,000 gallons is about twice the water-only charge in every block. AWE notes that “both water and wastewater rates must be considered when evaluating the savings related to shower-to-toilet graywater systems.”
  • Households sit in the first block. JXN’s first block runs to 50 CCF a month, about 37,400 gallons. A household rarely gets past it, so its marginal rate is $10.00 per 1,000 gallons.
  • Larger buildings save at higher rates. An apartment building or hotel whose bills reach 151 CCF or more a month saves $23.33 to $26.67 per 1,000 gallons, more than twice what a household saves on the same gallon.
  • Fixed charges stay. The monthly availability charge depends on meter size, not use, so it does not shrink when the building reuses water.

There is one more catch. JXN water-only, sewer-only and irrigation-only accounts pay about half the combined rate. If greywater replaces water that runs through a separate irrigation meter, it saves the irrigation rate, not the combined one. AWE also warns that landscape systems save nothing on sewer where sewer is billed at a flat rate or on winter use; under JXN’s meter-based billing, water saved on a combined account does lower the sewer charge.

The rate side of Jackson’s bill is not what rules greywater out. An EPA-led 2021 study that modeled greywater membrane bioreactors (MBRs, biological treatment followed by membrane filtration) in large buildings found that where they reached cost parity, local rates were “at least $9 per 1000 gallons” (Arden and others, Water Research, 2021). That study compared costs with drinking water rates. In Jackson, each gallon of city water a system replaces avoids a combined charge of $10.00 to $26.67 per 1,000 gallons. Scale, piping and operating cost decide most projects here.

A single-family home: why the numbers rarely work

For one household, greywater toilet flushing almost never pays back within the life of the equipment. The flushing demand is too small, the household’s rate is in the lowest block, and even modest operating costs eat most of the savings. Efficiency upgrades and, where allowed, simple laundry-to-landscape systems are the cheaper ways to save water at home.

Example (fictional). The same fictional household of four replaces 9,344 gallons of city water a year (25.6 gallons a day for 365 days). In the water savings calculator, at JXN Water’s first-block combined rate of $10.00 per 1,000 gallons, that avoids $93 a year. AWE’s operating assumptions, $1 per 1,000 gallons plus $36 a year of maintenance, come to about $45, leaving net savings of $48 a year. On AWE’s example installed cost of $3,000, the calculator shows a simple payback of 61.9 years, about four times the 15-year life AWE assumes. These are illustrative figures, not quotes.

AWE’s own table reaches the same conclusion across the country. For a four-person home and a $3,000 system, it shows paybacks of 102 years at a combined rate of $8 per 1,000 gallons, 52 years at $11 and 35 years at $14, and it concludes that shower-to-toilet systems “are unlikely to be cost-effective to homeowners except in cases where household occupancy is very high, and/or water rates are very high, and/or system costs are much lower than the $3,000 cost assumed.”

How high is very high? Using AWE’s operating assumptions, a $3,000 system needs net savings of about $200 a year to pay back in 15 years. At Jackson’s $10.00 first-block rate, that takes about 26,000 gallons of flushing a year, or roughly 11 people on 1.28-gallon toilets in one home, by our arithmetic. Few households qualify.

What a household can do instead

The efficiency path is cheaper and saves more. EPA estimates that replacing old toilets with WaterSense labeled models saves a family nearly 13,000 gallons a year. At JXN’s first-block rate, 13,000 gallons is about $130 a year, more than the $93 a greywater system could ever save for the example household. Fixing leaks comes first of all; the water use calculator helps compare an estimate with the bill.

Laundry-to-landscape systems are the low-cost greywater option. AWE puts installed costs at “as little as a couple hundred dollars for a do-it-yourself laundry-to-landscape system to more than $5,000 for a professionally installed pumped system,” with minimal operating costs for the simplest types. Savings depend on how many days you would otherwise water. AWE estimates them as 8.7 gallons of laundry water per person per day, times 75 percent, times the number of people and the number of watering days. For example, suppose a household of four would water on 150 days a year: that is about 3,900 gallons, or about $39 a year at $10.00 per 1,000 gallons.

In Mississippi, check the rules before diverting any drain. MSDH’s on-site wastewater regulations define wastewater to include “bath and toilet waste, residential laundry waste, residential kitchen waste” (MSDH On-Site Wastewater Regulations), and a text search found no greywater provisions in them. EPA advises keeping greywater irrigation below the surface and consulting “local health department officials first.” The legal layers are covered in is it legal to collect rainwater or reuse greywater in Mississippi.

Apartment buildings: where scale starts to help

Apartment buildings improve every number in the payback formula. More people flush every day, the building’s bills reach higher rate blocks, and the operating cost of one treatment system is spread across many units. Whether it pays then depends on piping, operating cost and installed cost, which is why new construction is the natural place for it.

Example (fictional). Briarmoor Apartments is a fictional 48-unit building with 96 residents on one master meter. Suppose its bills reach about 230 CCF in a typical month, so its last gallons fall in JXN Water’s 151 to 350 CCF block at $23.33 per 1,000 gallons. With AWE’s 10.6 gallons of shower water per person, five flushes at 1.28 gallons and 10 percent treatment loss, the greywater calculator shows 916 gallons collected and treated a day against 614 gallons of flushing demand: 100 percent of flushing covered, 301 gallons left over, and 224,256 gallons of city water saved a year. The water savings calculator turns that into $5,232 a year of avoided water and sewer charges. To show the arithmetic only, enter the calculator’s own example figures of $2,400 a year to operate and $60,000 installed (it labels both as examples, not prices): net savings are $2,832 a year and the simple payback is 21.2 years. All figures are planning assumptions for a fictional building.

The more useful question for an owner is the reverse: how much can the building afford to spend? Turn the formula around. The installed cost that pays back in a target number of years equals net annual savings times those years. For Briarmoor’s $5,232 of avoided charges, the table shows the break-even installed cost at three hypothetical operating costs.

Hypothetical operating cost per year Net savings per year Installed cost that pays back in 15 years In 20 years
$1,000 $4,232 $63,480 $84,640
$2,000 $3,232 $48,480 $64,640
$3,000 $2,232 $33,480 $44,640

Every $1,000 of yearly operating cost removes $15,000 from what the system can cost and still pay back in 15 years. Operating cost deserves as much attention in bids as the equipment price.

Piping decides most retrofits

A greywater system needs two separate pipe networks: drains that carry shower and lavatory water to the treatment unit, and a purple-labeled supply that carries treated water back to the toilets. FEMP says greywater reuse “requires retrofitting the plumbing system for existing buildings” and that dual plumbing “can be integrated into the design with less labor” in new construction (FEMP, Best Management Practice 14). In an occupied building, that piping can cost more than the treatment equipment, and no published US figure was found to estimate it. Bids for the specific building are the only reliable number.

Equipment that fits the flow

Treatment units for multifamily and commercial buildings are listed under NSF/ANSI 350 in Class C, which NSF defines as “Multi-family residential units and commercial facilities.” On NSF’s listing current as of November 21, 2026, Class C units for laundry and bathing water were rated from 79 to 7,926 gallons a day, and the two Class R units for single-family homes at 52.8 and 260 gallons a day (NSF/ANSI 350 listings). Briarmoor’s 614 gallons a day sits inside the Class C range. The greywater recycling service page explains how Maredes specifies equipment by class and capacity, and how a system works from drain to bowl is covered in greywater toilet flushing.

Scale and the EPA model

The EPA-led 2021 study found strong economies of scale. Its membrane bioreactor systems became more cost-competitive than rainwater or condensate systems above about 500,000 gallons a year. In its set of large mixed-use buildings in cities with published rate data, 9 percent of greywater MBR systems cost no more per gallon than local drinking water. By our arithmetic, reaching 500,000 gallons a year from toilet flushing alone takes about 214 people on 1.28-gallon toilets. For apartment owners, EPA’s NEWR calculator offers a screening-level estimate of cost and environmental impact by ZIP code and is recommended for “buildings with 50 or more occupants” (EPA, NEWR Calculator).

Hotels: steady demand, harder piping

Hotels have the flushing demand and usually the rate block to make greywater worth a look, but occupancy swings and existing piping often decide against it. Every guest who checks out takes both supply and demand with them, and a hotel built without separate drains from its guest bathrooms faces a piping retrofit on every floor.

Example (fictional). The greywater calculator’s default example is the fictional Pearlbank Hotel at 70 percent occupancy, about 134 guests, each assumed to use 16 gallons in the shower and 3 at the sink and to flush 5 times a day at 1.28 gallons, with 10 percent lost in treatment. The result is 2,291 gallons collected and treated per day against 858 gallons of flushing demand: 100 percent of flushing covered, 1,434 gallons left over and 313,024 gallons of city water saved a year. At the site’s example combined rate of $23.33 per 1,000 gallons, the water savings calculator puts that at about $7,303 a year before operating cost. In the hotel’s water review, greywater for toilet flushing was screened and not chosen, because the existing building has no separate drain and supply piping. All figures are planning assumptions.

Occupancy moves the result directly. Using the calculator’s per-guest assumptions, each 10 points of occupancy at the Pearlbank is about 19 guests and 123 gallons of flushing a day, worth roughly $1,040 a year at $23.33 per 1,000 gallons, by our arithmetic. A hotel that runs at 50 percent in winter and 85 percent in summer has a system sized for one season and underused in the other.

The Pearlbank’s planned path went to laundry rinse recycling and a rain and condensate tank instead; the example project shows why. What hotels that did install greywater systems had to manage, from guest complaints to monitoring, is covered in greywater recycling in hotels.

The costs payback estimates leave out

Energy, laboratory testing and maintenance labor are the operating costs most often missing from greywater payback estimates. Energy is usually small in dollars, though for most system types it carries more carbon per gallon than city water; testing can be the biggest single line; maintenance depends on who is on site to do it.

Energy

Greywater systems use electricity for pumps, aeration, disinfection and controls. The UK Environment Agency’s 2010 study assumed 0.6 kilowatt-hours per cubic meter for short-retention systems serving one or two toilets, 1.5 for small biological systems, 2.5 for larger systems and 3.5 for small MBRs (UK Environment Agency, 2010). The EPA-led 2021 study modeled 0.75 to 1.1 kilowatt-hours per cubic meter for greywater MBRs of about 1,000 to 11,000 gallons a day. The Portuguese study used about 1.8.

System type and sourcekWh per cubic meterkWh per 1,000 gallonsElectricity cost per 1,000 gallons at 10.93 cents per kWh
Short retention, 1 or 2 toilets (UK Environment Agency)0.62.3$0.25
Greywater MBR, about 1,000 to 11,000 gallons a day (EPA-led study, 2021)0.75 to 1.12.8 to 4.2$0.31 to $0.46
Small biological system (UK Environment Agency)1.55.7$0.62
Treatment in a Portuguese single-family house (Frontiers, 2025)1.86.8$0.74
Larger multimedia or MBR systems (UK Environment Agency)2.59.5$1.03
Small MBR (UK Environment Agency)3.513.2$1.45
Sources: UK Environment Agency, Energy and carbon implications of rainwater harvesting and greywater recycling (2010), Table 12; Arden and others, Water Research (2021); Pimentel-Rodrigues and Silva-Afonso, Frontiers in Environmental Science (2025); U.S. EIA, Mississippi Electricity Profile 2024, average retail price 10.93 cents per kWh. Conversions (1,000 gallons = 3.785 cubic meters) and costs are our arithmetic; checked November 2026.

Against avoided charges of $10.00 to $26.67 per 1,000 gallons in Jackson, electricity is a small share of the bill side: about $230 a year for Briarmoor’s 224,256 gallons at 2.5 kilowatt-hours per cubic meter, by our arithmetic. AWE’s $1 per 1,000 gallons for chemicals and energy is in the same range.

Laboratory testing

Testing is where greywater differs most from other reuse. The Portuguese study lists the monitoring its national specification calls for in operation: E. coli, enterococci, pH, BOD, suspended solids, turbidity and ammonia monthly; Legionella, Pseudomonas, nitrogen and phosphorus twice a year; and residual chlorine monthly where chlorine is used. That full set costs “no less than €1,200” a year in Portugal, more than twice the studied house’s yearly mains water bill, which does not exceed €500, and the authors found it “difficult to predict a cost of less than €200/year” even with risk-based reductions. They conclude that greywater systems “may not be a good economic option” in buildings with significant health risks, such as hospitals and nursing homes, because their monitoring must be demanding.

In the United States, the monitoring a project needs is set by the local approval, and laboratory fees are billed as quoted by the laboratory. EPA recommends disinfection “for all water used indoors for toilet flushing or other uses” (EPA WaterSense at Work, Section 8), and confirming that disinfection works means sampling. Price the sampling plan before you price the equipment.

Maintenance and reliability

The UK Environment Agency found that most of the installations it reviewed needed more maintenance than guidance documents stated, partly to fix faults. For basic filter-and-disinfectant systems, an earlier Environment Agency review it cites reported filters that needed regular cleaning, odor problems, variable reliability, and “instances where the system had failed and switched to mains back-up with users unaware of the failure.” A system that silently runs on city water saves nothing while still costing power and service.

AWE adds smaller items that still belong in the operating line: backflow prevention devices that some jurisdictions require, with periodic testing at the owner’s cost, and permit fees. FEMP’s maintenance list starts with inspecting the system for leaks and blockages. A service plan with scheduled filter, membrane and lamp changes and a maintenance log is part of the operating cost, not an extra.

Design, approval and space

Some costs arrive before the first gallon. A system needs drawings and a specification, a review by the local building official and, where wastewater is involved, the health department, and an inspection after installation; FEMP lists “system inspection after installation to verify compliance” among typical local requirements. Where the local authority requires an engineer’s seal on the drawings, a licensed engineer provides it. The equipment also needs a room with a floor drain, power and space to change cartridges and membranes. In a new building that room is a line on the plans; in an existing one it may displace storage or parking.

Questions to ask before you accept a bid

Bids for greywater systems are hard to compare unless they answer the same questions. Ask each bidder in writing:

  1. Which NSF/ANSI 350 class and rated daily capacity does the treatment unit carry, and where is it on NSF’s current listing?
  2. How many kilowatt-hours does the system use per 1,000 gallons delivered, including pumping to the toilets?
  3. Which filters, membranes, UV lamps and chemicals need replacing, how often, and at what current price?
  4. What sampling does the design assume, how often, and for which parameters?
  5. What happens when treatment fails: does the system switch to city water, and does it raise an alarm someone will see?
  6. Who services it, how quickly, and what does a yearly service contract cost?
  7. What do the piping, the separate drains and the purple-labeled supply cost, separately from the equipment?

The answers to questions 2 through 6 are your operating cost, and the answer to question 7 is often the largest part of the installed cost.

Carbon, sewers and other effects beyond the bill

Greywater’s wider effects cut both ways. It reduces demand on the city’s supply and the volume sent to the sewer, but most treated greywater systems use more energy per gallon than city water, and lower flows can affect sewers. These effects rarely change a payback, but they matter to owners with carbon targets.

The UK Environment Agency found that, with one exception, operational energy and carbon intensities were “over 100 per cent” higher than mains water “for most greywater applications.” The exception is “short retention greywater systems which are around 40 per cent less carbon intensive than mains water supply.” The EPA-led study found that the environmental impact of greywater MBRs depends heavily on the local electricity grid. EPA’s onsite reuse page, on the other side, notes that reusing water onsite can “reduce the volume of water entering a sewer system” and lower energy used to transport treated water (EPA, Onsite Non-Potable Water Reuse Resources).

The Portuguese authors flag one more effect: widespread greywater use lowers flows in public sewers, which can impair the movement of solids and leave treatment plants below the flows they were designed for. For one building in a city system, this is a planning note, not a reason to stop.

When greywater recycling is worth it: a decision table

Greywater recycling is most likely to pay where the building has many steady occupants, efficient fixtures already installed, a high combined rate on its last gallons, new or opened-up piping, and staff or a contract to run it. It is least likely to pay in a single home, an occupied building with closed walls, or a facility whose health risks call for demanding monitoring.

What greywater toilet flushing can avoid on a Jackson bill Water and sewer charges avoided per year, before operating cost Household of 4 $10.00 per 1,000 gal 48 residents $20.00 per 1,000 gal Briarmoor, 96 residents $23.33 per 1,000 gal Pearlbank, 134 guests $23.33 per 1,000 gal 214 residents $26.67 per 1,000 gal $93 $2,243 $5,232 $7,303 $13,332 $0 $3,500 $7,000 $10,500 Gallons: people x 5 flushes x 1.28 gallons x 365 days (Pearlbank: calculator default)
Example (hypothetical and fictional) buildings for illustration; the Pearlbank Hotel and Briarmoor Apartments are fictional. Method: AWE (2017) and the site's greywater and water savings calculators; rates from JXN Water's blocks effective March 23, 2026; our arithmetic, checked November 2026. Operating and installed costs are not included.

The chart shows why building size dominates. The same gallon is worth up to 2.7 times as much at the top block as in the first, and a 214-resident building flushes more than 50 times the water of one household. The table turns those levers, and the costs above, into a screen you can run before paying for a design.

Factor Leans toward worth it Leans against
People flushing every day About 200 or more steady occupants: apartments, dormitories, busy hotels One household, or large seasonal swings
Fixtures Efficient toilets already installed, so savings are real Old toilets still in place: replace them first
Rate on the last gallons Top blocks, $23.33 to $26.67 per 1,000 gallons combined First block, or water on a separate irrigation meter
Piping New construction or a renovation that opens every bathroom wall Occupied building with closed walls and no separate drains
Operating cost A sampling plan and service cost priced before bids Testing and maintenance left out of the estimate
People to run it Maintenance staff on site or a service contract No one checking filters, disinfection or alarms
Health risk Housing, offices, hotels with a water management program Hospitals and nursing homes, where monitoring must be demanding
Approval A local official and health department willing to review it No path to approval

How to run the numbers for your own building

Running the numbers takes an afternoon with the bills and the site’s calculators; deciding takes bids and an approval path. Work through the steps in this order:

  1. Get twelve months of bills. Find the monthly use in CCF and the block your last gallons fall in, and note any separate irrigation meter.
  2. Fix and upgrade first. Find leaks and replace toilets over 1.6 gallons per flush; the water use calculator helps check where water goes.
  3. Count people and flushes. Use real occupancy by month, not capacity, and your actual gallons per flush.
  4. Run the greywater calculator. Take the city water saved per year, not the greywater collected.
  5. Run the water savings calculator. Use your top block rate and a written operating cost that includes sampling, power, parts, backflow testing and service.
  6. Work backward to an affordable installed cost. Multiply net savings by 15 years and compare with bids that include piping.
  7. Screen with EPA’s NEWR calculator if the building has 50 or more occupants.
  8. Ask the local building official and the health department what approval would require before you commission a design.

A Maredes water review does this screen with your bills and a walk of the building, and it ends with findings in order of cost, so fixes and fixtures come before any reuse system. If greywater survives the screen, the engagements page describes the design package and pilot options, and the water reuse section covers the alternatives. Questions about a specific building can go through the contact page. Every figure above is an estimate, not a promise of savings or payback.

Have a building in mind?

If this article describes a question about your home, property or business, tell us about the building. A project starts with a water review and a written summary of what we found.