Maredes homeRequest a water review
Menu

Water review and lab testing

A Maredes water review reads your bills, walks the building and sends samples to a certified lab, then explains what is in the water and where it goes.

For: Owners and managers of homes, apartments, hotels, restaurants and small commercial buildings

A clear glass sample bottle with a white cap hangs from a thin string, its neck above the waterline and its body filling slowly below the surface.

Every Maredes project starts here. Before anyone recommends a filter, a softener or a recycling loop, we find out two things: what is in your water, and where your water goes. The water review answers both, in writing, for one building. Many owners stop after it and act on it themselves. Others continue to system design.

What a water review covers

A review has three parts. Each produces something you keep.

1. Your bills and records

We read twelve months of water and sewer bills. The bills show how much water the building uses, how use changes with the seasons, and what each thousand gallons costs once water and sewer charges are added together. A sudden jump in one month often points to a leak or a stuck irrigation valve, which is cheaper to fix than anything we could design.

For city water we also read your utility’s annual Consumer Confidence Report. Every community water system must publish one, listing the contaminants it detected and how the results compare with federal limits, as the EPA explains. The report describes the water leaving the treatment plant. It cannot describe what happens in your service line and your building’s own pipes, which is why the review also samples at your taps.

For a private well there is no utility report. The EPA is clear that well owners are responsible for the safety of their own water, so we ask for the well log, its depth and any past tests.

2. A walk through the building

We walk from the meter to the roof with someone who knows the building. We note fixture types and flow rates, the water heater, any treatment equipment already installed, the laundry and kitchen, cooling equipment that drips condensate, roof drains and downspouts, and the space available for equipment: a closet, a mechanical room, a garage wall or a pad outside. Photos go into the review so you can see what we saw.

3. Sampling and laboratory tests

We take samples at the taps that matter (usually the kitchen and one other point) and send them to a laboratory certified for drinking water analysis. State certification programs, overseen by the EPA’s laboratory certification program, set the methods and quality controls those laboratories follow. The test list depends on the source and the question:

Building and question Typical tests
City water, taste or scale complaints Hardness, iron, chlorine or chloramine, pH, total dissolved solids
City water, older building or lead service line concerns Lead and copper (first-draw samples), plus the above
Private well Total coliform and E. coli, nitrate, arsenic, iron, manganese, hardness, pH
Reuse planning (greywater, laundry, rain, condensate) Turbidity, organic load and bacteria in the source water, measured over more than one day

We do not test for everything by default. A long panel costs more and rarely changes the decision. If a result is above a limit, we say so plainly and tell you who to call: the utility for city water, the health department for a well.

What you receive

Example (fictional). For the Pearlbank Hotel, a fictional 96-room hotel, the review found about 10,000 gallons of city water on an average day, with laundry, landscaping and guest rooms as the largest uses. It recommended fixing two running toilets first, then designing a laundry rinse water recycling system and a rain and condensate tank for irrigation. The full walkthrough is on the example project page.

The written review includes:

  • A water balance: how many gallons enter the building on an average day and roughly where they go (guest rooms or bathrooms, laundry, kitchen, cooling, landscaping, leaks).
  • Lab results explained: each result beside the federal limit or guideline that applies, in plain language, with the laboratory’s original report attached.
  • Findings in order of cost: what to fix first (leaks and fixtures often come before treatment), what treatment the results justify, and what they do not.
  • A reuse screen: whether greywater, laundry rinse water, rainwater or condensate is worth a closer look for this building, with rough daily volumes.
  • Questions that remain: anything we could not confirm, such as code approval for a reuse system or a result that needs a second sample.

How long it takes and what you provide

The building walk takes one visit. Laboratory turnaround depends on the tests and the laboratory, so we give you the expected dates when we schedule the visit rather than a promise up front. Before the visit, please gather what is on the water review checklist: bills, any past tests, a floor plan or sketch, and access to the meter, the equipment room and the roof.

You can check your own numbers first. The water use calculator estimates daily use from fixtures and habits, and the water test reader compares results you already have with EPA limits. For context, the EPA estimates that each American uses an average of 82 gallons of water a day at home.

What happens next

The review is a standalone engagement with its own fee, quoted before the visit. You can stop there. If you continue, the findings become the brief for system design, and the lab results become the baseline that the start-up test is compared with. See engagements for how the options fit together and how we work for every step.

Start with a water review.

Tell us about the building: what it is, who uses it, where the water comes from and what you would like to change. We reply with questions and a time to walk the building with you.