Home water test kits are accurate enough to screen some things and not accurate enough to decide others. When the San Francisco Public Utilities Commission (SFPUC) compared three kit brands with laboratory methods in more than 400 tests, all three agreed with the laboratory more than 80 percent of the time for coliform bacteria, nitrate, nitrite and iron, one brand had data quality problems for lead, copper, pesticides and chlorine, and two brands agreed less than 60 percent of the time on pH. For anything that drives a health or spending decision, such as lead, bacteria in a well, nitrate where an infant drinks the water, or buying treatment equipment, EPA directs people to a state-certified drinking water laboratory, and in Mississippi MSDH publishes the list.
This guide covers what the SFPUC evaluation found, what kits and laboratories do differently, a decision table for which test fits which question, and the routes to a certified test in Mississippi, including free data for city customers and the state and university options for well owners. Every source was checked on November 22, 2026.
Are home water test kits accurate? What a utility’s evaluation found
The most useful public evidence comes from a water utility that tested kits against its own laboratory. SFPUC found kits gave “reasonable agreement with laboratory methods” overall, but agreement varied widely by test and by brand.
In late 2018 and early 2019, SFPUC evaluated three brands of home test kits, using “over 400 tests, including both kit and laboratory methods.” Its home test kits page reports:
- Coliform bacteria, nitrate, nitrite and iron: greater than 80 percent agreement with the laboratory for all three brands.
- Pesticides, lead, copper and chlorine: greater than 80 percent agreement for two brands, “but data quality problems were seen with one of the brands.”
- pH: less than 60 percent agreement for two brands; the third agreed between 60 and 80 percent.
- Total hardness and alkalinity: less than 60 percent agreement for all three brands on San Francisco’s soft water, which SFPUC attributes to levels “at the low end of the kits’ detection levels.” Follow-up tests on waters of moderate to high hardness gave greater than 80 percent agreement for all three.
What the evaluation does and does not show
Read these results for what they are. They come from one utility’s water, three brands and one period. SFPUC’s own summary table is footnoted “Conducted on San Francisco drinking water, 2018/2019,” and kits change. The study did not test arsenic, PFAS or radon, so it gives no evidence either way about kits for those.
The pattern still carries over. Tests that are simple yes-or-no or that sit well inside a kit’s range did well, and tests near the bottom of a kit’s range did badly. SFPUC also warns that kits “can sometimes produce misleading results, such as when a color strip or indicator line doesn’t fully develop,” that “the kit result is misinterpreted by the kit user,” and that for lead “some kits can provide variable results depending on the brand.”
Mail-in kits are not automatically laboratory results
Some kits ask you to fill a bottle and mail it to a laboratory. SFPUC cautions that “some products utilize laboratories that have not been certified and use methods that should not be relied on to make decisions about safety.” Its conclusion covers every kit: “Home test kit results should be considered an initial step, not a final result,” and a poor result should be confirmed by a laboratory using “certified methods, and quality control measures to ensure accuracy and reliability.”
What a home kit can and cannot tell you
Kits use three reading methods, and each fails in its own way. Knowing which you are holding tells you how far to trust it.
SFPUC describes the formats: test strips “with color charts to estimate concentrations,” presence or absence strips “based on the appearance of one or two lines,” and bacteria tests that show “the formation of gas bubbles and color change after a 48-hour period.”
| Kit format | Used for | How it reads | Where it goes wrong |
|---|---|---|---|
| Color strip | Estimating a concentration | You match the strip’s color to a printed chart | Colors that do not fully develop; low levels at the edge of the chart; reading in poor light |
| Two-line strip (positive or negative) | Lead and pesticides in all three brands SFPUC evaluated | Which line is darker decides the result | Reading the strip in the wrong direction; very faint lines; false positives |
| Bacteria vial | Total coliform | Color change or gas bubbles after incubation | Contaminating the vial during collection; reading before the full incubation time |
Sources: SFPUC home test kits page (formats, examples, failure modes).
Reading a two-line strip
All three brands SFPUC evaluated used two-line strips for lead and pesticides, and “it is important that the strips are read in the proper direction.” SFPUC’s key: no lines or very light lines mean the test was inconclusive; a darker left line, or only a left line, means negative; a darker right line, or two equally dark lines, means positive. In its evaluation, a positive pesticide strip “was determined to be a false positive via laboratory testing.”
Running a bacteria vial
Bacteria tests fail most often at collection. SFPUC asks users to avoid “touching, coughing, or sneezing on any part of the inside of the test vial,” to take water “directly from a flowing kitchen tap and not from a water pitcher or glass,” and to “wait the entire incubation time (typically 48 hours but could vary by home test kit).” In the kits it tested, yellow indicated a positive result, and some kits also showed gas bubbles.
A positive home bacteria result on a private well is a reason to call MSDH or a certified laboratory for a proper sample, not to start treating on the kit alone. A negative result is one snapshot. EPA’s well guidance asks owners to test at least yearly and again after floods, repairs or any change in the water.
What a certified laboratory does that a kit cannot
A certified laboratory result is worth more because the whole chain is controlled: the bottle, the preservative, the temperature, the time to analysis, the method and the records. Certification itself is granted method by method and analyte by analyte.
EPA’s laboratory certification page explains that public water systems “use state-certified laboratories to regularly test drinking water samples using methods evaluated and approved by EPA.” It encourages individuals who want independent testing “to contact a state-certified drinking water laboratory” and adds: “Unfortunately, EPA is unable to test residential or commercial drinking water upon request.”
What “certified” means in Mississippi
MSDH’s Environmental Laboratory Certification Program inspects and certifies laboratories inside the state and honors out-of-state laboratories by reciprocity. For reciprocity, the laboratory’s home certifying authority must send MSDH a document listing “each analyte, the method used, its certification status, and its date of expiration,” along with its latest on-site evaluation and proficiency testing results.
That detail matters to a buyer of a test. A laboratory can be certified for bacteria and not for metals, or for lead by one method and not another. MSDH’s in-state list, checked November 22, 2026, showed five participating laboratories, three certified for microbiology only and two for both chemistry and microbiology. MSDH notes that “the status of a laboratory may change” and takes questions at 601-576-7582. Ask any laboratory, in state or out, for its certification for the exact analyte you want tested.
How a laboratory sample differs from a kit sample
EPA’s Region 8 Laboratory publishes a quick guide to drinking water sample collection, written for trained samplers. A few of its rules show why a laboratory result is more than a better strip:
| Step | Laboratory sample (EPA Region 8 guide) | Typical home kit |
|---|---|---|
| Container | Supplied by the laboratory; sterile 125 or 150 mL bottles for coliform; a wide-mouth 1 liter bottle for a first-draw lead sample | A vial or cup in the box |
| Preservative | Sodium thiosulfate for chlorinated coliform samples; acids or bases for many chemical tests | Usually none |
| Timing | Lead first draw after at least six hours of standing water; coliform samples kept below 10 C and analyzed within 30 hours | Whenever you open the kit |
| Tap choice | A cold tap without softener or point-of-use filter for lead; screens left in place | Any tap |
| Records | A chain of custody form for each sample | None |
| Analysis | A certified method, quality control and a reporting limit | A color or a line read by eye |
The guide also tells samplers to “check with the laboratory before collecting samples” and says “it is best to obtain sampling supplies directly from the laboratory performing the analyses.” For a home tester, that is the practical rule: order the bottles from the laboratory and follow its sheet.
When a kit is enough and when you need a laboratory
Use a kit to answer a curiosity or a maintenance question, and a certified laboratory for any decision about health, a sale, a lease or a purchase of treatment. The table below sorts common questions using the SFPUC results and EPA and MSDH guidance.
| Your question | Kit result is enough? | Why | Better route |
|---|---|---|---|
| Is my hard water hard enough to need a softener? | Often, on moderately hard water | Kits agreed with the lab more than 80 percent of the time on harder water, under 60 percent on soft water | Confirm with a laboratory hardness result before sizing equipment |
| Is chlorine reaching my tap? | As a screen | Two of three brands agreed more than 80 percent; one had data problems | Your utility’s annual report gives the disinfectant level |
| What is my pH? | No | Two of three brands agreed with the lab less than 60 percent | Laboratory pH, ideally with the rest of a well panel |
| Is there lead at my kitchen tap? | No | Results varied by brand, and EPA says testing at a certified laboratory is the only sure way | Certified laboratory, first-draw sample |
| Is my well free of bacteria? | No | A positive needs confirmation, and a negative is one snapshot | MSDH, MSU’s well program or a certified laboratory |
| Is nitrate safe for an infant’s formula? | No | EPA’s MCL is 10 mg/L, and infants under six months “could become seriously ill” above it | Certified laboratory |
| Arsenic, PFAS or other chemicals | No | Not covered by the SFPUC evaluation | Certified laboratory for each analyte |
| Did my new filter or softener change anything? | For hardness, as a check | The claim you paid for deserves a measured answer | Laboratory sample before and after treatment |
Sources: SFPUC home test kits page; EPA basic information about lead and National Primary Drinking Water Regulations; MSDH private well testing page.
The nitrate line deserves emphasis. EPA’s drinking water regulations set nitrate at 10 mg/L (as nitrogen) and say infants below six months who drink water above that “could become seriously ill and, if untreated, may die.” A strip that reads near the limit cannot tell you which side you are on.
Example (fictional). A family on a rural well in Hinds County uses a $20 strip kit after a wet spring. The nitrate pad lands between two colors near the 10 mg/L block, the hardness pad reads high, and the bacteria vial stays clear after 48 hours. Because a baby is due in the fall, they order a well panel from a certified laboratory for total coliform, E. coli, nitrate, pH, hardness and total dissolved solids, using the laboratory’s bottles. The report shows nitrate at 6.2 mg/L, below EPA’s 10 mg/L limit, total coliform present and E. coli absent. They call the MSDH Division of On-Site Wastewater about disinfecting the well and retesting, and plan a second nitrate test after the next heavy rain. Every number here is invented for illustration.
Start with the free data if you are on city water
If a public water system serves your building, part of the testing has already been done and published. Read the annual Consumer Confidence Report before you buy a kit or order a test.
EPA says community water systems must send this report to customers “each year by July 1,” listing the water’s source, detected contaminants, the health effects of any violation and contact numbers. MSDH’s Consumer Confidence Reports page says every community public water system in Mississippi “is required to prepare and make available to all customers” a report, and posts the reports systems provide for 2022 to 2025. MSU Extension notes that the report “must list detected contaminants in the water supply, as well as the amount and source of the contamination.”
How to read the table in the report
Most reports print one row per detected contaminant. JXN Water’s 2025 Water Quality Report is a typical layout, and its definitions apply to most reports:
| Column | What it means |
|---|---|
| Violation Y/N | Whether the system broke the rule for that contaminant during the year |
| Level detected | The number used for compliance: a highest value, an average or a 90th percentile, depending on the rule |
| Range of detects | The lowest and highest single results, often more useful to a household than the average |
| MCLG | “The level of a contaminant in drinking water below which there is no known or expected risk to health” |
| MCL | “The highest level of a contaminant that is allowed in drinking water” |
| AL (action level) | “The concentration of a contaminant which when exceeded, triggers treatment or other requirements” |
| Likely source | Where the contaminant usually comes from, such as erosion of natural deposits or household plumbing |
Source: JXN Water, 2025 Water Quality Report, “Terms and Abbreviations” (quoted definitions).
Read the range column with the level. In the same report, the surface system’s lead 90th percentile for January to June 2025 was 4.5 ppb, but single results ranged from not detected to 192 ppb. The level tells you whether the system met the rule; the range tells you that some taps differ a great deal from the typical one. MSDH’s Drinking Water Watch database shows the same kinds of records for any Mississippi public system, including violations and lead summaries by period.
What the annual report cannot tell you
The report describes the water the system delivers, measured at its sampling points. It does not describe your service line, your pipes or your faucet, which is where lead usually enters. For Jackson’s 2025 and 2026 results and what they mean at the tap, see is Jackson tap water safe to drink. For how to check the pipes themselves, see how to tell if you have lead pipes.
So for city customers the useful tests are narrow: lead and copper at the taps you drink from, and anything the report flags that you want to confirm at your own tap. In Jackson, JXN Water’s lead page lists the Mississippi Public Health Laboratory (601-576-7582) for lead testing, and JXN Water’s 2025 report invites customers concerned about lead to call 601-500-5200.
Testing a private well in Mississippi
If your water comes from your own well, nobody else is testing it. Mississippi offers three routes: MSDH for bacteria, a certified private laboratory for everything else, and periodic screenings through MSU Extension’s Mississippi Well Owner Network.
EPA’s private wells page says private wells are “not regulated by the Federal Government under the Safe Drinking Water Act nor by most state governments,” and that a USGS study of 2,100 private wells found “about one in five” had a contaminant above a human-health benchmark. MSU Extension’s Publication 2775, using fiscal 2018 data, counted 382,398 Mississippians, 12.81 percent of the state, on private wells, including 24,413 people in Hinds County.
The three routes
MSU Extension’s publication P3813 lists the options for well owners:
- A private laboratory. Use one certified for the analytes you need.
- The MSDH Division of On-Site Wastewater (1-855-220-0192). An MSDH environmentalist visits the well and takes a sample in a sterile container. “There is a fee for having your private well water tested.” The sample goes to the state laboratory in Jackson for total coliform, and if that is positive, a second test for E. coli. MSDH’s private well testing page confirms it “tests private wells for bacteriological contamination only,” with minerals and chemicals going to a private laboratory, and offers an online request form.
- MSU Extension’s Mississippi Well Owner Network (662-325-1788). The network runs screenings and workshops. In 2025, for example, it offered free screenings in Tate County: owners picked up approved containers, dropped off samples on April 24, and had them screened for total coliform and E. coli, with PFAS sampling kits for the first 21 interested owners.
What to test, and how often
EPA’s well guidance says to test “annually for total coliform bacteria, nitrates, total dissolved solids, and pH levels,” more often if small children, elderly adults or someone pregnant or nursing lives in the house, and immediately after flooding, land disturbance, repairs to the well or any change in odor, color or taste. MSU’s publication recommends testing at least once a year. EPA also lists conditions that call for extra tests:
| If you notice or live near | EPA says to consider testing for |
|---|---|
| Plumbing or service lines that contain lead | pH, lead, copper |
| Intensive agriculture | Nitrate, nitrite, pesticides, coliform bacteria |
| Stained fixtures or laundry | Iron, copper, manganese |
| Scaly residue, soap that will not lather | Hardness |
| Objectionable taste or smell | Hydrogen sulfide, corrosion, metals |
| A landfill, factory, gas station or dry cleaner | Volatile organic compounds, total dissolved solids, pH, sulfate, chloride, metals |
| Recurring stomach illness | Coliform bacteria |
Source: EPA, Protect Your Home’s Water, “Identifying reasons to test your water.”
If bacteria come back positive
MSU’s publication is plain: total coliform is reported as present or absent, and “any presence of total coliform is unacceptable”; for E. coli “there is no acceptable range.” If the second sample is positive for E. coli, “do not drink the water without boiling it first” and consult MSDH. MSDH’s disinfection page describes shock chlorination and a follow-up bacteriological sample. Samples dropped at a county health department the same day go overnight to the Public Health Laboratory, which “normally takes approximately 24 hours” to analyze them; samples taken straight to the Jackson laboratory must arrive within 28 hours of collection. The private well checklist collects these steps.
After a flood or a well repair
EPA lists flooding, land disturbance and any repair or replacement of part of the well system among the reasons to test “immediately.” MSDH’s well disinfection page gives the household procedure: for example, 4 cups (1 quart) of unscented household bleach in 5 gallons of water poured down the well, followed by more chlorinated water, left to stand “for at least 8 hours and preferably 24 hours,” then pumped “until no chlorine is present in the water” before a bacteriological sample is taken. MSDH warns not to drink the solution and says that if two attempts do not clear the contamination, “a licensed water well contractor should be contacted.” A kit has no role in that sequence; the clearance sample goes to the laboratory.
How to collect a sample that means something
Most bad results come from bad samples. Whether you use a kit or a laboratory, the collection rules are similar, and the laboratory’s own instructions always come first.
- Get the right container. For a laboratory test, use the bottles the laboratory sends. For bacteria, the bottle must be sterile, so do not rinse it, touch the inside or set the cap down.
- Pick the right tap. For lead, EPA’s guide says to use a cold tap “free from devices that are designed to change the water composition, such as water softeners or point of use filters,” and not to remove the screen. For a general sample, a kitchen or bath tap high enough to fit the bottle without touching it works.
- Get the timing right. For a first-draw lead sample, let the water stand at least six hours and do not flush before that period starts; collect the first water out of the tap. For other tests, the guide says to flush the line first, “generally 2 to 3 minutes,” until the temperature steadies.
- Keep it cold and quick. Coliform samples go in a cooler with ice and reach the laboratory within the holding time. EPA’s guide gives 30 hours for drinking water samples and suggests delivering the day of collection where possible.
- Write it down. Note the tap, the date, the time, how long the water stood and anything unusual. A laboratory will ask for this on its chain of custody form.
- Sample before and after treatment if you are checking a filter or softener, so you can see what the equipment changed.
For a lead service line, a single bottle tells only part of the story. EPA’s guide notes that profiling a lead service line can take “8 to 10 sequential sample bottles,” depending on how far the line is from the tap. That is a laboratory exercise, not a kit one.
Reading the report and acting on a result
A laboratory report gives a number, a unit, a reporting limit and often a reference value. Reading it well means checking the unit, comparing with the right standard and confirming anything surprising before you spend money.
MSU’s publication notes that most results are in milligrams per liter, which equals parts per million; micrograms per liter equal parts per billion. A lead result of 0.005 mg/L is 5 ppb. The water test reader takes your values in the units on the report and shows each next to EPA’s maximum contaminant level, action level or secondary standard, flagging anything above. Treat its output as a screening comparison and ask the laboratory or MSDH about anything you do not understand.
Units, reporting limits and “not detected”
| On the report | Means | Example |
|---|---|---|
| mg/L | Milligrams per liter, the same as parts per million (ppm) | Nitrate 2.1 mg/L |
| µg/L | Micrograms per liter, the same as parts per billion (ppb); 1,000 µg/L = 1 mg/L | Lead 5 µg/L = 0.005 mg/L |
| ND or “<” a number | Not detected at or above the laboratory’s reporting limit | “<1 µg/L” means below 1, not zero |
| Present or absent | A yes-or-no bacteria result | Total coliform absent |
| As CaCO3 | Hardness or alkalinity expressed as calcium carbonate | Hardness 150 mg/L as CaCO3 |
Sources: MSU Extension P3813 (units; present or absent results); JXN Water 2025 Water Quality Report (“ppb: parts per billion or micrograms per liter”; “ND: Non-Detected”). Example values are illustrative.
A “not detected” result is only as good as the reporting limit behind it. If you are testing for lead because a child lives in the house, ask the laboratory what its reporting limit for lead is before you order, so a “not detected” result means something against EPA’s health goal of zero.
Two habits keep you from over or under reacting. First, retest before acting on a single surprising result: EPA tells well owners whose results exceed a health standard to contact the health department and “have your well re-tested to confirm.” Second, remember what standards apply to. EPA’s drinking water standards bind public water systems; for a private well, they are the reference you compare against, and the decisions are yours.
Example (fictional). A small office on city water has a break room tap and an ice machine. The manager buys a strip kit, which shows moderately hard water and a positive line on the lead strip. She orders a first-draw lead test from a certified laboratory for both points, collected after the building sat over a weekend. The break room tap comes back at 4 ppb and the ice machine supply at 2 ppb. The manager keeps the reports, cleans the break room aerator and sets a monthly reminder to flush both points on Monday mornings. A later laboratory hardness result confirms the strip’s reading, and she uses it to compare scale-reducing options for the ice machine. Every detail here is invented for illustration.
When a result points to treatment
Choose treatment from a laboratory result, not a strip. Certification is specific to the contaminant, so a filter certified for lead is not certified for nitrate or bacteria, and the treatment selector matches each problem to the treatment and certification that can address it. If PFAS is your concern, our article on whether water filters remove PFAS covers when testing and a filter make sense.
Hardness is the one case where a home result often starts the conversation. Softeners are sized in grains per gallon, while laboratories report hardness in mg/L as calcium carbonate; the water test reader converts one to the other, so 150 mg/L as CaCO3 shows as about 8.8 grains per gallon. Even then, size equipment from a laboratory number, because the SFPUC results show how far strips can drift at the low end of their range, and a softener sized to a wrong reading regenerates too often or too seldom.
For a building with several problems at once, such as hardness, iron staining and an old service line, test them together in one laboratory panel. One set of bottles, collected the same day, lets the results be read against each other: iron and manganese explain the staining, pH and alkalinity explain corrosion, and lead and copper show whether that corrosion reaches the tap.
Testing more than one tap: landlords and small businesses
A building with several units or several drinking points needs a plan, not one sample. The water can differ from tap to tap, and EPA’s lead guidance says each home’s plumbing gives different results, so one kitchen sample does not describe a whole building.
A simple plan for a small building looks like this:
- List every drinking point. Kitchen taps, break room sinks, ice machines, coffee brewers, bottle fillers and drinking fountains. Note which are used every day and which sit idle.
- Choose the points that tell you the most. The tap farthest from the meter, the one closest to it, any point on old plumbing, and any point that serves children, pregnant staff or food preparation.
- Match the test to the risk. Lead and copper first-draw samples where plumbing predates 1988 or the service line is lead, galvanized or unknown. Bacteria where a well supplies the building or after a long shutdown. Hardness where scale is the complaint.
- Sample on a normal day. A first-draw lead sample needs at least six hours of standing water, so the first draw on a weekday morning fits most offices and shops.
- Record and repeat. Keep the reports by tap, retest after any plumbing work, and test again on a schedule you can keep.
MSDH’s guidelines for food facilities in Jackson, dated February 26, 2016, ask operators to flush every drinking point “before first consumption each day” and to change ice machine and dispenser filters as the manufacturer recommends. Testing tells you whether those routines are enough at your taps. Whether you must test, or share results with tenants or customers, depends on your business and local rules; ask the regulator or your own counsel.
What testing costs, and mistakes that waste the money
Costs vary by laboratory and by the list of tests, so get a written quote before you collect anything. A few published figures help set expectations:
- Lead. EPA’s lead basics page says testing “costs between $20 and $100.” Its Protect Your Tap guide gives $15 to $100.
- Private well bacteria through MSDH. MSU’s publication says “there is a fee,” without a figure; ask the Division of On-Site Wastewater when you call.
- Free options. EPA’s well guidance notes that your local health department “may provide private well testing for free,” and MSU’s Mississippi Well Owner Network has run free screening events, such as the 2025 Tate County screening for total coliform and E. coli.
- City customers in Jackson. JXN Water’s 2025 report asks customers who want a lead test to call 601-500-5200, and its lead page lists the Public Health Laboratory at 601-576-7582. MSDH’s 2016 food facility guidance mentioned a $20 lead sampling kit for Jackson customers; that is an old figure, so call for the current one.
A free or low-cost kit is not a bargain if it leads to the wrong purchase. If a vendor offers a free test as part of selling equipment, ask which laboratory analyzes it and whether that laboratory is certified for each analyte, as SFPUC’s caution about uncertified laboratories suggests.
Common mistakes that waste a test
Most disappointing results trace back to a handful of avoidable errors. Each one below comes from the collection rules in EPA’s guide or SFPUC’s kit advice.
- Sampling through a filter when you want to know what the pipes deliver. EPA’s guide says lead samples come from a tap without a softener or point-of-use filter.
- Flushing before a first-draw lead sample. The guide says not to flush before the six-hour standing period starts.
- Removing the aerator before a lead sample. The guide says to leave screens in place for lead and copper samples.
- Pouring bacteria samples from a pitcher or glass. SFPUC says to sample directly from a flowing tap.
- Reading a bacteria vial too early. Wait the full incubation time on the box, typically 48 hours.
- Missing the holding time. A coliform sample that reaches the laboratory late may be rejected; EPA’s guide gives 30 hours for drinking water samples.
- Buying treatment on one strip. SFPUC calls a kit result “an initial step, not a final result.”
What to do next: a testing plan in five steps
Most households need one good laboratory test of the right things more than a drawer of kits. A short plan keeps the cost down and the results usable.
- Read what is already published. On city water, read your Consumer Confidence Report and your utility’s notices. On a well, find any past tests and the well log.
- Write down your question. Lead for a child, bacteria after a flood, hardness before buying a softener, nitrate for an infant. The question decides the test.
- Use a kit only for the questions it answers well. Hardness on harder water, a first look at chlorine, or a quick check between laboratory tests.
- Order the rest from a certified laboratory. Confirm its certification for each analyte, use its bottles and follow its sheet. Well owners can start with MSDH for bacteria and MSU’s network for screenings.
- Keep every report and compare them over time, especially before and after any treatment.
The water review checklist lists what to gather before anyone looks at your building. Maredes is a Jackson company that designs water treatment and reuse systems for one building at a time, and as how we work describes, every project starts with a water review and sampling by a certified laboratory, with the laboratory’s report attached. Homeowners on city water or a well can see how that applies on our homes page, and the drinking water hub lists related articles. If you want help planning the tests, you can request a water review. This article is general information, not medical or engineering advice; for health questions about a result, ask your doctor or MSDH.
