Private well checklist for Mississippi owners
A private well has no utility behind it. The owner does the testing, the wellhead care and the follow-up, and this list covers each part.
For: Homeowners and small building owners on a private well in Mississippi

Checklist
City water comes with a utility that tests it and a regulator that checks the utility. A private well has neither. EPA notes that private wells are “not regulated by the Federal Government under the Safe Drinking Water Act nor by most state governments,” which leaves testing and upkeep to the owner. That is a lot of owners in Mississippi: MSU Extension, using MSDH data for fiscal 2018, counted 382,398 people (12.81 percent of the state) on private wells, including 24,413 in Hinds County.
This checklist is for homeowners and small building owners on a well. It has four sections. Tick items as you confirm them and print or download the list; nothing is saved when you leave the page.
Testing
EPA’s advice is to test a private well every year for total coliform bacteria, nitrates, total dissolved solids and pH, and to test right away if there are known groundwater problems in the area, conditions near the well change (flooding, land disturbance, new construction), any part of the well system is replaced or repaired, or the water’s odor, color or taste changes. EPA suggests testing more often if small children, older adults or someone pregnant or nursing lives in the home.
The checklist adds a one-time baseline for arsenic, lead, iron, manganese and hardness. EPA names lead pipes, faucets and fixtures as the most common sources of lead in drinking water, and iron, manganese and hardness decide what treatment the well needs. A USGS study that EPA cites found that about one in five private wells tested had at least one contaminant above a human-health benchmark.
Where to test matters. MSDH “tests private wells for bacteriological contamination only”; testing for minerals and chemicals goes to a private laboratory. MSDH publishes a list of laboratories certified for drinking water, and notes that a laboratory’s status can change. Keep every report: a series of results shows changes a single test cannot. The water test reader compares results with EPA values; its default example is a fictional well report with iron and manganese above EPA’s secondary standards.
The wellhead
Contamination can enter from the surface, so this section covers the cap, the casing and what sits around them. A sealed, screened cap is meant to keep out insects and runoff; a casing that rises above the ground, with ground sloping away, keeps surface water from running down the outside. Keep fuel, fertilizer and pesticide away from the well, and the septic system at the distance the health department requires. EPA’s testing chart links nearby activities to tests: intensive agriculture nearby calls for nitrate, nitrite, pesticide and coliform tests, and buried fuel tanks or a gas station call for volatile organic compound tests. An abandoned well on the property is a direct path to groundwater; ask a licensed water well contractor about plugging it properly.
After a flood
Do not drink well water after a flood until the well has been disinfected and tested. Have the pump and wiring checked before the power goes back on.
MSDH publishes a well disinfection procedure. In outline: mix unscented chlorine bleach with water (for example, 1 quart of bleach in 5 gallons of water), put it in the well, let it stand at least 8 hours and preferably 24, then pump until no chlorine remains and take a bacteriological sample. MSDH says its Public Health Laboratory analysis normally takes about 24 hours and that samples must reach the Jackson laboratory within 28 hours of collection. If coliform persists after two attempts, MSDH advises contacting a licensed water well contractor. Follow the full procedure on MSDH’s well disinfection page, not this outline.
Treatment equipment
Treatment should match a laboratory result, not a guess. Hard water points to a softener, which the softener sizing calculator sizes from your result; iron and manganese point to oxidation and filtration; bacteria point first to the wellhead and disinfection, then to treatment such as UV. The treatment selector lists what works for each problem and what does not.
Once equipment is in, change filters, UV lamps and softener salt on schedule and log each change. Then test again to confirm the treatment does what it was chosen to do. For a whole house on a well, Maredes designs whole-building filtration from a certified laboratory result; more on wells is on homes.
Start with a water review.
Tell us about the building: what it is, who uses it, where the water comes from and what you would like to change. We reply with questions and a time to walk the building with you.