Water softener sizing calculator
Start from a lab result, not a guess. Hardness, iron and daily use give the grains a softener removes each day and how often it regenerates.
For: Homeowners on a private well or city water, and managers of small buildings

Calculator
A water softener removes calcium and magnesium (hardness) by ion exchange until its resin is full, then regenerates with salt. Its size decides how often that happens. This calculator estimates the hardness load a building puts on a softener each day and how often a given unit would regenerate. It is for homeowners on a private well or city water and for managers of small buildings with scale on fixtures and equipment.
It needs your own hardness result. JXN Water’s 2025 Water Quality Report lists no hardness figure, and well water varies from one well to the next, so the only reliable number is a test of your water.
The method
- Compensated hardness = hardness in grains per gallon + 4 grains per gallon for each mg/L of dissolved iron. Iron uses up softener capacity too; adding 4 per mg/L is a common industry rule of thumb, not a standard.
- Grains removed per day = people x softened gallons per person per day x compensated hardness.
- Usable capacity = the softener’s capacity at your salt setting, minus a reserve of grains per day x reserve days, so soft water lasts through the day of regeneration.
- Days between regenerations = usable capacity divided by grains per day, rounded down.
- Regenerations per year = 365 divided by that number.
- Capacity for one regeneration a week = grains per day x (7 + reserve days).
The inputs and where to find them
- Hardness. From a laboratory report, usually as mg/L as calcium carbonate (CaCO3). Divide by 17.1 for grains per gallon. The water test reader does the conversion for you.
- Dissolved iron. In mg/L from the same report. EPA’s secondary standard for iron is 0.3 mg/L, a guideline for taste, staining and appearance.
- People. Usual occupants.
- Softened water per person per day. Count only water that passes through the softener. EPA estimates each American uses about 82 gallons a day at home, but outdoor taps and a separate drinking water line are often left hard, so 70 is the example’s assumption.
- Capacity at your salt setting. From the maker’s table. A softener’s rated capacity depends on how much salt each regeneration uses. Softeners are certified under NSF/ANSI 44, Cation Exchange Water Softeners.
- Reserve days. The example keeps one day in reserve.
The default example
Example (fictional). A household of four on a private well, with a fictional test result of 12 grains per gallon of hardness and 0.5 mg/L of dissolved iron, softening 70 gallons per person per day with a 32,000-grain softener and a one-day reserve. The calculator returns: compensated hardness (hardness plus 4 gpg per mg/L of iron) 14.0 grains per gallon; grains removed per day 3,920; days between regenerations 7; regenerations per year 52; capacity needed for one regeneration per week 31,360 grains.
Reading the result
In the example, the 32,000-grain unit sits just above the 31,360 grains needed for a weekly cycle, so it regenerates about once a week. A unit that regenerates every two or three days is undersized for the load, or its salt setting is low. If the calculator reports that the daily load exceeds the capacity left after the reserve, the unit is too small for the building.
The example’s iron (0.5 mg/L) is above EPA’s 0.3 mg/L secondary standard. A softener handles low levels of dissolved iron; higher iron, or iron that has already turned to rust particles, usually needs oxidation and filtration ahead of the softener. The treatment selector lists both.
Limits and next steps
A softener does one job. CDC notes that softeners remove calcium and magnesium but not microbes, and a softener is not a substitute for treatment certified for lead or other health-related contaminants. On a private well, test for bacteria and nitrate before anything else; the private well checklist lists the tests.
Salt use, water used in regeneration and the choice between time-based and meter-based control are not modeled here. They are part of a design for whole-building filtration, where Maredes matches the softener and any iron removal to the laboratory result and the space near the service entry. Homeowners can read more about homes on city water or a private well.
Start with a water review.
Tell us about the building: what it is, who uses it, where the water comes from and what you would like to change. We reply with questions and a time to walk the building with you.