Maredes homeRequest a water review
Menu

Laundromat water recycling: how it works and when it pays off

The reader questionCan a laundromat recycle its wash water, and when does it make financial sense compared with newer washers?

The round chrome-ringed glass door of a front-loading washer lies tilted at the waterline, the upper arc of its ring dry and the porthole glass below the surface catching the light.

Yes, a laundromat can recycle its wash water. A laundry water recycling system collects what the washers drain, screens out lint, filters out solids and soap residue, disinfects the water and sends it back to the washers, with city water topping up the difference. It makes financial sense after the washers themselves are efficient, in a store with high and steady volume, and where water and sewer together cost a lot per 1,000 gallons; in Jackson both are billed from the water meter, so every gallon recycled is a gallon not bought and not sent to the sewer.

How much it saves is documented, though mostly from hotel laundries. EPA puts complex recycling at more than 80 percent of washer water, and a federal demonstration by Pacific Northwest National Laboratory (PNNL) measured about 80 percent at a large Seattle hotel laundry. This article covers laundromat water usage, how recycling works, why efficient washers come first, what decides payback, a worked example on JXN Water’s rates, and the chemistry, space and permit questions to settle before buying.

How much water does a laundromat use?

A laundromat uses what its washers use times how often they turn, plus a little for restrooms and cleaning. Federal ratings let you estimate gallons per wash for most single-load machines; your meter gives the store total.

Gallons per wash, from the federal rating

Most self-service washers are covered by a federal standard. Under 10 CFR 431.152, a commercial clothes washer is a soft-mounted front-loading or top-loading machine with a drum of no more than 3.5 cubic feet (front-loading) or 4.0 cubic feet (top-loading), designed for use by more than one household, “such as multi-family housing common areas and coin laundries.”

The rating that matters is the integrated water factor (IWF): gallons of water per wash cycle for each cubic foot of drum capacity. Multiply the IWF by the drum size and you have the water a washer may use per wash under the federal test. Under 10 CFR 431.156, commercial washers made on or after January 1, 2018 must have an IWF of no more than 8.8 for top-loaders and 4.1 for front-loaders.

WasherIntegrated water factor (gal per cycle per cu ft)Example drumWater per wash at that rating
Commercial washer made before 20139.5 or less3.2 cu ft top-loaderup to about 30.4 gal
Top-loader made from 2018 (federal limit)8.83.2 cu ftup to about 28.2 gal
Front-loader made from 2018 (federal limit)4.13.0 cu ftup to about 12.3 gal
Most efficient ENERGY STAR commercial washers listedas low as 3.33.0 cu ftabout 9.9 gal
Multi-load and hard-mount washers outside the federal definitionno federal ratingup to 80 lb per loadfrom the specification sheet or a meter
Example drum sizes are hypothetical; water per wash is the rating times the drum size, our arithmetic. Sources: 10 CFR 431.152 and 431.156 (eCFR); EPA WaterSense at Work, Section 3.5, Laundry Equipment (May 2023), for the pre-2013 figure, the ENERGY STAR low of 3.3 and multi-load capacities. Checked November 2026. Real use varies with cycle settings.

EPA’s laundry equipment guide adds three useful facts. Commercial washers made before 2013 have an IWF of 9.5 or less. Multi-load machines in laundromats can be hard-mount (bolted to the floor) or soft-mount and hold up to 80 pounds, against less than 20 pounds for a conventional commercial washer. And washer extractors, the machines in on-premises laundries, usually need 2 to 4 gallons per pound of laundry.

The gap between machine types is the first lesson. At the federal limits, a front-loader uses less than half the water per cubic foot of a top-loader (4.1 against 8.8). ENERGY STAR says certified commercial washers use about 45 percent less water than standard models.

Turning machine counts into a monthly number

Two methods give you the store’s water use, and you should do both because they check each other.

  1. From the bill. Take twelve months of billed CCF, multiply by 748 gallons per CCF (the conversion on JXN Water’s rate page) and divide by the days in each billing period.
  2. From the machines. For each washer type, multiply gallons per wash by the number of machines and the average turns per day (washes per machine), using coin or card counts from the machines’ controllers. Add a small amount for the restroom, mop sink and cleaning.

For example, suppose a store has 30 front-loaders with 3.0 cubic foot drums at the 4.1 limit, each turning 5 times a day. That is up to about 12.3 gallons a wash, 150 washes and roughly 1,850 gallons a day, or about 74 CCF in a 30-day month before the restroom and mop sink. Swap in 30 pre-2013 top-loaders with 3.2 cubic foot drums at the same turns and the same arithmetic gives up to about 4,560 gallons a day, about 183 CCF a month, which on JXN Water’s table moves the store into a higher rate block as well.

If the bill is well above the machine estimate, look for leaks, a stuck fill valve, a water heater relief valve dripping to a drain, or machines running more water than their rating. The water use calculator can do the machine arithmetic: enter washes per week as clothes washer loads and your gallons per wash, and set the household fields to your staff restroom use or to zero.

Do laundromats recycle water?

Some do, but no public count tells you how many. What is clear is that the equipment exists, federal agencies describe it, and EPA lists commercial laundries among the applications for onsite non-potable water reuse, alongside toilet flushing, fire protection and vehicle washing.

EPA’s laundry guide describes two levels, and says either can be added to commercial washers, multi-load washers and washer extractors:

  • Simple recycling recovers the final rinse of one load for the first rinse of the next. EPA says this water “rarely needs treatment” and puts savings at 10 to 35 percent.
  • Complex recycling treats water from wash and rinse cycles for use in every cycle of the next load. EPA’s text says it “can save more than 80 percent of water used”, its savings table gives 85 to 90 percent, and it usually requires treatment.

A self-service store is a different setting from the hotel laundries in most published studies. In an on-premises laundry, a supervisor sorts linens by soil and a chemical supplier programs every wash formula. In a self-service store, each customer picks a machine, a cycle and usually a detergent, and loads range from work clothes to baby blankets. That variety is why the treatment stages, the storage time and the controls matter more in a laundromat than in a hotel.

Recycled laundry water stays in the laundry. It is non-potable water used again for washing, never for drinking, ice or a kitchen. If you have heard of greywater systems that send laundry water to toilets or landscapes, that is a different design with different rules; see our article on whether greywater recycling is worth it.

Simple or complex: which fits a self-service store

Simple recycling depends on controls that know when a final rinse is draining and when the next first fill is starting. Multi-load washers and washer extractors with programmable cycles are the natural place for it; EPA notes that some new washer extractors store the previous load’s rinse water for the next load on their own. Single-load coin or card machines run fixed factory cycles, so ask the manufacturer or distributor whether a rinse-capture setup is supported before assuming it.

Complex recycling is less fussy about controls, because the washers simply draw treated water from a supply line as they would draw city water. The price of that simplicity is the treatment train, the tanks, the electricity and the maintenance described below.

Question Points toward simple recycling Points toward complex recycling
Washer controls Programmable multi-load machines Fixed-cycle single-load machines
Share of water to recover 10 to 35 percent is enough to matter You want most of the washer water back
Space A small tank and a pump Room for tanks, filters and disinfection
Budget and staff time Low Higher capital and weekly attention

Apartment laundry rooms and care facility laundries

The same arithmetic applies outside laundromats, with different answers. An apartment laundry room usually has a handful of washers, often placed and serviced by a laundry route operator. ENERGY STAR’s commercial washer page notes that route operators can place equipment, provide maintenance and collect coins, and that operators and distributors can supply ENERGY STAR certified washers. For a small room, specifying certified front-loaders in the next route contract is likely to be the whole answer; recycling volumes are too small to carry the equipment.

Care facilities, hotels and other buildings with on-premises laundries run washer extractors with programmable formulas, a chemical supplier and much higher volume per machine. They fit the published research far better, and simple rinse recycling is often the first thing to test. Our article on ozone laundry versus water recycling covers that setting, and the laundry water recycling service page describes the feasibility study.

How a laundry water recycling system works

A complex recycling system is a short treatment train between the washer drains and the washer supply. The system PNNL measured is a good published example, described in its August 2014 report.

Washers drain Collection tank Lint screen (large solids) Pressure filters (solids, soap) Treated tank, kept disinfected UV before reuse Back to washers, labeled non-potable City make-up air gap or backflow preventer overflow and purge to sewer A complex laundry water recycling loop
Simplified diagram based on the treatment steps described in PNNL-23535 (August 2014) and the make-up and backflow practices in DOE FEMP Best Management Practice 14, checked November 2026. Actual systems vary by vendor; the city make-up connection and its protection are set by the local plumbing code.

The steps PNNL describes, in order:

  1. Collection. Washer discharge is pumped to a holding tank instead of going straight to the sewer.
  2. Lint removal. A vibrating lint removal system takes out large solids.
  3. Filtration. Pressure filters remove suspended solids, oil and grease, soaps and other organics.
  4. Storage with disinfection. Cleaned water goes to a recycle tank, where it is continually disinfected with oxidizing agents until a washer calls for it.
  5. Final disinfection. Before it goes back to the washers, the water passes ultraviolet light and ozone disinfection.
  6. Return and make-up. The washers draw from the recycling system, and a cold city water make-up line tops it up.

That make-up line is not small. At the Seattle site, PNNL calculated an average baseline of 14,990 gallons a day and measured 12,015 gallons a day of recycled water, so city water still supplied roughly 2,975 gallons a day. PNNL does not break down where that water went, so ask any vendor how much make-up its system needs and why. The make-up connection is also the point where non-potable and drinking water meet, which is why it needs backflow protection.

Vendors arrange the train differently, and some add stages. Ask any supplier for each stage, what it removes, what it does not remove, and how the system behaves when a stage fails.

Efficient washers first, then recycling

Replacing old top-loaders with efficient front-loaders usually cuts more water per dollar than recycling, and it changes the recycling case afterward. Do the washer decision first and size any recycling system to the water that is left.

The federal numbers make the reason plain. A pre-2013 top-loader with a 3.2 cubic foot drum may use up to about 30 gallons a wash; a front-loader meeting today’s 4.1 limit with a 3.0 cubic foot drum may use up to about 12. Every wash moved from the first machine to the second saves about 18 gallons with no treatment, no tank and no added electricity.

EPA’s laundry guide also points to cheaper steps that come before either:

  • Preset commercial and multi-load washers to their more water-efficient cycle.
  • Encourage full loads; a laundry scale near the machines helps.
  • Use detergents made for high-efficiency washers in the right amounts, since too many suds can leave clothes incompletely rinsed.
  • Consider cold-water washing; EPA notes that water heating takes about 90 percent of the energy it takes to run a clothes washer.
  • Submeter and watch for leaks and maintenance problems.

For multi-load washers too large for ENERGY STAR, EPA suggests choosing models that use no more than 4.0 gallons per cycle per cubic foot. For washer extractors, it points to machines with built-in rinse recycling that use less than 2.5 gallons per pound.

Situation Usually first Then consider
Mostly top-loaders made before 2013 Front-loading washers, starting with the busiest machines Recycling sized to what is left
Mostly front-loaders, high volume, high water and sewer rate Cycle presets, leak checks, submetering Complex recycling, or a pilot on one bank of machines
Multi-load or hard-mount washers with programmable cycles Cycle review with the equipment supplier Simple rinse recycling, then complex if volumes justify it
Low volume or low rate Cycle presets and maintenance Probably nothing more; the payback is long

What decides payback

Four numbers decide whether recycling pays in a laundromat: the water and sewer rate you avoid, the volume you recycle, the energy it adds or keeps, and what the system costs to buy and run. Vendor savings percentages are not on that list until a meter confirms them.

The rate you avoid

Recycling saves water you would have bought and sent to the sewer, so the combined rate is the driver. PNNL’s Seattle site paid $7.42 per 1,000 gallons for water and $15.57 for sewer in 2014, $22.99 combined, and PNNL calls that a relatively high rate.

Jackson’s 2026 rates are in the same range for a busy store. JXN Water’s combined rate is $14.96 per CCF from 51 to 150 CCF a month, $17.45 from 151 to 350 CCF and $19.95 above 350 CCF, which is $20.00, $23.33 and $26.67 per 1,000 gallons. The rate page says “Water and sewer services are based on water meter readings”, so a laundromat pays sewer on nearly every gallon its washers draw.

Savings come off the top of the bill. A store that uses 240 CCF a month saves at $23.33 per 1,000 gallons until its use falls below 150 CCF, then at $20.00. The fixed monthly availability charge, which depends on meter size ($200 for a 1.5-inch meter, $320 for a 2-inch meter), does not change.

Volume and steadiness

Recycling equipment costs about the same whether it runs two hours or twelve, so volume decides how fast it pays. PNNL’s recycling report recommends limiting outreach to facilities processing less than 1,500 pounds of laundry a day, because their volumes “may not be high enough to warrant the high capital investment.” Our article on ozone laundry versus water recycling walks through that threshold and the Seattle results in detail.

Steadiness matters too. A store that is busy every evening and weekend can size a smaller tank than one that sits idle for days, and short storage keeps treated water fresh.

Hot water at the washer

A laundromat pays to heat part of the water its washers draw, so water saved at the washer also saves gas or electricity. EPA’s laundry guide estimates the energy with the same method it uses for kitchens: 0.0006 thousand cubic feet (Mcf) of natural gas or 0.183 kWh of electricity per gallon for a 75°F rise, at a heater efficiency of 0.75 for gas and 1.0 for electric. It leaves the hot share of washer water as a facility-specific number, because customers choose the temperature.

Mississippi’s average commercial natural gas price was $12.46 per Mcf in 2025, according to EIA’s October 30, 2026 release. At EPA’s assumptions that is about $9.97 to heat 1,000 gallons with gas. At August 2026’s average commercial electricity price of 13.45 cents per kWh, electric heating comes to about $24.61 per 1,000 gallons.

Two practical points follow:

  • Front-loaders save energy twice. They use less water per wash, and every hot gallon they do not draw is also a gallon the water heater does not heat.
  • Recycling’s energy story depends on temperature. If treated water returns warmer than city water, the heater does less work, as PNNL measured in Seattle. If it cools in storage, the saving is mostly water and sewer, minus the added electricity.

To find your hot share, read the gas or electric meter that serves the water heater for a few typical days, or ask the installer for a temporary meter on the hot water line. A store whose customers mostly wash cold will see less energy benefit from any water measure than one whose customers wash warm.

Energy: warm water kept, electricity added

Recycling adds electricity for pumps, controls and UV lamps. At Seattle, PNNL measured 1,922 kWh a month added against 365,000 gallons a month recycled, about 5.3 kWh per 1,000 gallons. At Mississippi’s average commercial electricity price of 13.45 cents per kWh in August 2026, that is about 71 cents per 1,000 gallons recycled.

Recycling can also keep heat. The Seattle system reheated recycled water and returned it warm, saving an average of 1,119 therms a month of hot water heating. Whether a laundromat system keeps much heat depends on how warm customers wash and how long water sits in the tank, so treat any heat credit as something to measure, not assume.

Capital, operating cost and incentives

PNNL reported the vendor’s average capital cost for such systems at about $100,000 in 2014, varying widely with capacity and design, and noted that the Seattle installation received a $39,620 incentive from Seattle Public Utilities. Those are 2014 figures for a large hotel laundry, not prices for a laundromat. No federal or state source we found publishes current installed prices for laundromat recycling systems, so any cost figure you see online is a vendor’s or an installer’s. The cost drivers are predictable: the recycled flow the system must deliver at the store’s busiest hour, the number of treatment stages, tank sizes, the plumbing changes to collect drain water (often the most variable item in an existing building), electrical work, and permits. Get written bids for your store, and include filters, UV lamps, sampling and service in the operating cost.

A worked example: the Ironweed Laundromat

A fictional store shows how the order of decisions changes the answer. The numbers are planning assumptions built from the federal ratings and JXN Water’s rates.

Example (fictional). The Ironweed Laundromat is a fictional self-service store on JXN Water. It has 36 single-load top-loaders with 3.2 cubic foot drums, bought before 2013 and assumed to use their full 9.5 rating, about 30.4 gallons a wash, at 4 turns a day. It also has 12 multi-load front-loaders whose specification sheets list 36 gallons a wash, at 3 turns a day. Restrooms, a mop sink and cleaning add about 226 gallons. That is about 5,900 gallons a day, or about 237 CCF in a 30-day month.

The owner compares three options:

  • Option A: replace the top-loaders with 3.0 cubic foot front-loaders at the 4.1 federal limit (about 12.3 gallons a wash). Saving: about 2,606 gallons a day, 44 percent of the store’s water.
  • Option B: add complex recycling to the existing machines, assuming it replaces 60 percent of washer water. That is a cautious planning figure, well below EPA’s range for on-premises laundries, because customer loads and detergents vary. Saving: about 3,404 gallons a day.
  • Option C: do A, then B on the remaining washer water. Saving: about 4,447 gallons a day in total.

Every number here is a planning assumption for a fictional store, not a measurement or a quote.

Reading JXN Water’s table as an inclining block schedule, where each rate applies to the use within its block, the fictional store’s monthly usage charge changes like this:

Option Monthly use Usage charge per month Lower by Other changes per month
Today about 237 CCF about $3,381
A: front-loaders about 132 CCF about $1,602 about $1,780 about $312 less gas, if 40% of the water saved was gas-heated
B: recycling only about 100 CCF about $1,123 about $2,258 about $72 more electricity at PNNL’s rate of use
C: front-loaders, then recycling about 58 CCF about $498 about $2,884 about $312 less gas; about $39 more electricity
Monthly water and sewer usage charge, fictional store Today $3,381 A: front-loaders $1,602 B: recycling only $1,123 C: front-loaders, then recycling $498 Usage charge only; the meter's availability charge is the same in every case.
Example (fictional) data for illustration: planning assumptions for a fictional store, priced at JXN Water's combined water and sewer rates from March 23, 2026 (read as an inclining block schedule), with washer water from 10 CFR 431.156 and EPA WaterSense at Work Section 3.5. Checked November 2026.

The payback picture follows from the table. Suppose, for illustration only, that recycling costs $6,000 a year to operate in filters, UV lamps, sampling and service, on top of the added electricity:

  • Recycling alone (Option B) would net about $20,200 a year, so an installed cost of $60,000 pays back in about 3 years, $100,000 in about 5, and $150,000 in about 7.4.
  • Recycling after new washers (the B part of Option C) would net only about $6,800 a year, because there is less water to recycle and the savings fall into a cheaper block. The same installed costs would take about 9, 15 and 22 years.

That is the main lesson of the example. Recycling looks best on a store full of old machines, but the same money spent on front-loaders captures much of the saving first, and what is left may not carry a recycling system. A store already full of efficient front-loaders should expect recycling to pay back slowly unless its volume or its rate is high.

The water savings calculator runs the same arithmetic on your own numbers: gallons replaced a day, days open, your top block rate, yearly operating cost and installed cost from bids.

Detergent, hardness, lint and linen quality

Chemistry is where laundry recycling succeeds or fails. EPA’s guide says recycling “may also require adjustments in chemicals and detergents” and tells owners to “contact the chemical supply vendor in any retrofit planning.”

In Seattle, PNNL reports that once the system was integrated and the chemical detergent program was adjusted, it worked as expected, with no drop in linen quality and no rise in guest complaints. That laundry had a chemical supplier tuning each formula. A self-service store usually does not, so the questions shift:

  • Customer detergents. Ask the vendor how the system handles varied detergents, softeners and bleach, and whether any products should be discouraged with signs at the machines.
  • Dissolved minerals. Lint screens, filters and disinfection are aimed at solids, soap residue and microbes, which is how PNNL describes the Seattle train. Ask how the system manages dissolved minerals and salts that pass through, and how much fresh make-up it needs to keep them in range.
  • Hardness. Ask a certified laboratory for a hardness test of your incoming water as part of any feasibility study. Hard water affects detergent performance with or without recycling.
  • Lint. Lint screens need regular cleaning; ask for the schedule, the labor and where the lint goes.
  • Odor and color. Ask what alarms tell staff that treated water is out of range, and what the system does then, ideally switching the washers to city water automatically.

The test that matters to customers is clean, fresh-smelling clothes. A pilot system on one bank of machines for a fixed term, with written measures, lets you check that before committing the whole store.

Space, storage, maintenance and measured results

A recycling system needs floor space, a drain, power and someone who looks after it every week. PNNL notes that wastewater recycling systems “can require up to several hundred square feet of floor space,” and that most central laundry areas do not have room to spare. In a laundromat that space often comes out of the back room or the customer floor.

Storage time is a design choice with health consequences. Warm, nutrient-rich water left sitting can grow bacteria, which is why the Seattle system kept its recycle tank continually disinfected and added ultraviolet light before reuse. EPA’s alternative water guide recommends disinfection for pathogens for all water used indoors, and our page on standards and safety explains how reuse systems are kept separate from drinking water. Size tanks for hours of use, not days, and drain them for long closures.

PNNL reported that after start-up such systems “typically require little maintenance apart from filter replacements.” A realistic maintenance plan still lists:

  • Lint screen cleaning and filter changes on the manufacturer’s schedule.
  • UV lamp replacement and sleeve cleaning.
  • Tank inspection and cleaning.
  • Checks of level sensors, valves, alarms and the make-up backflow protection.
  • Readings from a flow meter on the recycled water line, so savings are measured rather than assumed.

A written maintenance log and a service plan keep those tasks on a schedule.

Measuring the savings after start-up

Savings are real only if a meter shows them. PNNL could not meter a before period at Seattle, because the system was already running, so it built an engineered baseline: city make-up water plus recycled water, the amount the washers would have drawn without the system. The same method works for any store.

  1. Before installation, record at least three months of daily or weekly meter readings and machine counts, so you know gallons per wash for your store.
  2. Install two flow meters: one on the city make-up line to the recycling system and one on the recycled water line to the washers.
  3. Each month, add the two readings to get what the washers drew, and divide the recycled volume by that total to get the share recycled.
  4. Compare gallons per wash before and after, using the machines’ counts, so a busy or slow month does not distort the result.
  5. Log electricity for the system if it has its own circuit, and record filter, lamp and service costs as they happen.
  6. Check the bill. The drop in billed CCF should match the recycled volume, less any change in washes.

A simple monthly report with those six lines tells you whether the system is doing what the bid said, and it gives you evidence if a vendor’s warranty or service terms come into question.

Permits and codes in Mississippi

Mississippi has no state rule written specifically for onsite non-potable reuse, so approval is decided project by project by local officials. EPA’s onsite reuse page lists the states with onsite non-potable reuse regulations or guidelines: California, Colorado, Florida, Georgia, Hawai’i, Minnesota, New Mexico, Ohio, Oklahoma, Oregon, Texas and Wisconsin. Mississippi is not on the list.

Plumbing work still needs permits. The City of Jackson says “Property owners or licensed contractors are responsible for obtaining required permits before beginning work and scheduling required inspections.” Other cities and counties have their own building departments.

The Department of Energy’s Federal Energy Management Program describes the usual protections for non-potable systems in its Best Management Practice 14: installation according to local plumbing codes by licensed plumbing contractors, backflow preventers to separate potable and non-potable supplies, and non-potable reclaimed water pipes color coded with purple tags or tape. For a laundromat, that means:

  1. Ask the local building official early which plumbing code edition applies and whether the recycling system needs a permit, an inspection or an engineer’s drawings.
  2. Protect the city supply. The make-up line to the recycle tank needs an air gap or a backflow preventer, and anything installed on the city side should be certified lead free.
  3. Label the recycled water piping as non-potable along its whole run.
  4. Ask the sewer utility whether a smaller, more concentrated discharge raises any question under its rules for commercial customers.
  5. Write it down. A short code path memo records who approved what, which code applies, and how backflow, labeling and monitoring are handled.

EPA’s alternative water guide advises consulting local health department officials before installing a gray water treatment system. Water reused inside a laundry is not the same as gray water sent to toilets or landscapes, but a short call to the county health office costs little and settles the question for your project.

This is general information, not legal or engineering advice. Local authorities decide what your project needs.

What to do next

Start with your own numbers, then decide in order: washers, settings and leaks, then recycling sized to what is left.

  1. Turn twelve months of bills into gallons a day, and estimate washer water from ratings, machine counts and turns.
  2. Read the meter at closing and again an hour later to rule out leaks.
  3. List every washer with its type, drum size, age and rating; mark top-loaders made before 2013.
  4. Price front-loader replacement for the busiest machines at your top block rate.
  5. Only then ask recycling vendors the questions above, and compare their figures with the water savings calculator.

Questions to ask before you buy

A vendor’s savings percentage is a starting point, not a result. These questions turn a sales conversation into something you can check against your meter.

  1. How many gallons a day will the system return to the washers at my store’s volume, and how was that figure calculated?
  2. What does each treatment stage remove, and what does it leave in the water?
  3. How much city make-up water will the system still need, and where does purge water go?
  4. How long does treated water sit in storage on a slow day, and how is it kept disinfected?
  5. How much electricity does it use per 1,000 gallons recycled, measured, not estimated?
  6. What does a year of filters, lamps, service visits and sampling cost?
  7. What happens when an alarm trips: do the washers switch to city water automatically?
  8. Can I see metered results from a self-service store, not only a hotel laundry?
  9. Will you support a trial on one bank of machines with a flow meter on the recycled line?
  10. What permits did similar installations need, and who pulled them?

Maredes designs laundry water recycling for on-premises laundries and laundromats, and every design starts with a feasibility study that can recommend against recycling. Our page for offices, clinics, laundromats and other small businesses shows where a laundromat fits, and the commercial water section of the journal collects related articles. A water review covers bills, meters, machines and a certified lab test of your water. When you have your bills in hand, write to us.

Have a building in mind?

If this article describes a question about your home, property or business, tell us about the building. A project starts with a water review and a written summary of what we found.