Maredes homeRequest a water review
Menu

Why boil water notices are issued and what it takes to lift one

The reader questionWhy do water systems issue boil water notices, who issues them in Mississippi, and what testing is needed before they are lifted?

Bubbles rise from the floor of the tank in a rolling column and break the surface in a small dome of turbulence, while a stainless ladle rests across the rim above the waterline.

A boil water notice is issued when a water system loses pressure, makes a repair, or finds a sign that bacteria could be in the pipes, so that people boil water for one minute before drinking it until tests show the problem has passed. In Mississippi, the water system issues a “self-imposed” precautionary notice, and the Mississippi State Department of Health (MSDH) issues a “state-imposed” notice after an E. coli result or a serious failure. MSDH’s guidelines require pressure restored, the pipes flushed, chlorine checked, and then clear bacteria samples: one round to release a precautionary notice, two consecutive rounds to release a state-imposed one.

This article explains the rules behind each step, where they come from, and how long they usually take. It uses Jackson’s record as a dated example and ends with what a building owner does once a notice is lifted. Every rule cited was checked at its source on November 22, 2026. Rules and notices change, so always follow the notice you actually received.

What a boil water notice is, and how it differs from other advisories

A boil water notice tells people served by part or all of a water system to boil tap water before drinking or cooking with it, because germs could be present. It is one of three kinds of drinking water advisory, and the other two call for different action.

The CDC’s overview of drinking water advisories, dated March 4, 2024, describes the three:

Advisory What it means What to do
Boil water Tap water could contain germs; “boiling kills germs in the tap water that could make you sick” Use boiled or bottled water to drink and prepare food
Do not drink The concern is a chemical or toxin that boiling does not remove Use bottled water for drinking and cooking
Do not use Contact with the water could be dangerous Use bottled water for all purposes

The CDC’s instruction for a boil water advisory is to “bring water to a full rolling boil for 1 minute,” or 3 minutes above 6,500 feet. JXN Water’s notice page gives Jackson customers the same one-minute rule and lists the uses it applies to: “cooking or baking, making ice cubes, taking medication, brushing teeth, washing food, mixing baby formula or food, mixing juices or drinks, feeding pets, washing dishes, and all other consumption.”

Notice, alert or advisory

The words vary by agency. MSDH’s notice pages use “boil-water notice,” its 2016 guidelines use “Boil-Water Alert,” and the CDC uses “advisory.” They describe the same instruction. This article uses “notice” throughout.

What boiling does not fix

Boiling addresses germs only. EPA’s lead page says “boiling water does not remove lead from water,” and the CDC’s do not drink category exists because boiling does not remove chemicals. A boil water notice is about microbes in the distribution pipes, not about lead from a building’s own plumbing or any chemical result. Those have their own rules and their own notices.

Why boil water notices are issued

Most notices follow a loss of pressure. When a pipe breaks or a section is shut down for repair, pressure drops, and water from outside the pipe can be drawn in. MSDH’s guidelines for issuing a boil-water notice, revised December 1, 2016, give the sample notice text: “When a distribution system loses pressure, contaminants can siphon back into the water. Public health officials consider any system that loses pressure contaminated until tests prove otherwise.”

The four state triggers

The guidelines list when MSDH’s Bureau of Public Water Supply issues a state-imposed notice:

  1. A water system receives an E. coli result for a Revised Total Coliform Rule routine sample or re-sample.
  2. A system “loses pressure or the system is compromised and there is a significant probability that contamination can or will enter the potable water supply,” and the system’s officials have not issued the notice themselves.
  3. “A catastrophic event or natural disaster occurs.”
  4. A groundwater system that does not provide 4-log inactivation of viruses finds E. coli in a source water sample under the Groundwater Rule.

The two system triggers

The same document says a water system “should issue a ‘self-imposed’ Boil-Water Alert” when:

  • “The system loses pressure on all or part of the system,” or
  • “There is reason to believe the system is compromised and there is the possibility that all or part of the water system can or will become contaminated.”

What a typical notice says

Current MSDH notices follow this pattern. The notice for the Town of Utica in Hinds County, issued November 13, 2026 and released November 20, 2026, read: “Water system officials have issued a precautionary boil-water notice for the affected area described above due to loss of pressure caused by a line break. Boiling water before drinking can help prevent possible contamination from bacteria that may enter broken water lines.” JXN Water describes each of its notices as “a precautionary notice. It is the result of repair work performed on the water system. It does not mean that your water is unsafe, but it does mean that you must take precautions and boil your water before use.”

So a precautionary notice usually means “we know the pressure dropped,” not “we found bacteria.” A state-imposed notice can mean either a serious failure or a confirmed E. coli result. The notice text tells you which.

Who issues boil water notices in Mississippi

There are two issuers, and the difference decides who can lift the notice and how much testing it takes. MSDH’s water safety notices page explains: “Individual water systems issue precautionary safety notices when water pressure is lost,” and “when water testing by the MSDH Public Health Laboratory indicates problems related to water quality, MSDH immediately sends a state-issued water safety (boil-water) notice to the public via press release and this website.”

Self-imposed (precautionary) State-imposed
Issued by The water system’s officials MSDH, Bureau of Public Water Supply
Typical cause Loss of pressure, a repair, a suspected compromise E. coli result, serious pressure loss the system did not act on, disaster, E. coli in a vulnerable groundwater source
Who tells customers The water system, “using whatever means necessary” MSDH by press release and its website; the system still notifies customers directly
Posted on MSDH’s site If the system properly notifies MSDH Yes
Clear sample rounds to release (2016 guidelines) One round (the system may choose two) Two consecutive rounds
Who releases it The water system Only the Bureau of Public Water Supply

Sources: MSDH guidelines (revised December 1, 2016) and MSDH water safety notices page, checked November 22, 2026.

MSDH would rather the system act first

The 2016 guidelines say: “In most cases, it is preferred that the water system officials issue the alert.” MSDH steps in “if there is a significant threat to public health, the water system has failed to take the initiative in potentially hazardous situations, and/or the water system needs assistance.” The guidelines close with a plain statement of priority: “We must all be willing to err on the side of protecting public health rather than worrying about a customer’s temporary inconvenience.”

How the system tells customers

The guidelines put the duty on the system: “You are responsible for ensuring adequate notification, not MSDH.” For a few customers, they suggest “personal contact, door-hangers, or notes taped to their doors.” For a large area, radio, television and newspapers, plus signs, texts, email or automated calls. They also ask systems to consider “sensitive populations such as the elderly and young children.”

Where to check

Because two bodies issue notices, check two lists. MSDH posts statewide notices, and on November 22, 2026 it listed 16 active notices, none for the City of Jackson system. JXN Water posts its own precautionary notices by street; the same day it listed six, dated November 13 to 20, 2026, each covering about 6 to 55 connections. Both are snapshots. Check both pages for current notices.

How to read a boil water notice

A notice is short, but each line answers a question you need answered. EPA’s quick reference guide lists the elements a public notice must contain, and an MSDH or JXN Water notice maps onto them. Read a notice in this order.

Line on the notice What it tells you What to do with it
Issuer and system name, with PWS ID Who issued it: the water system (self-imposed) or MSDH (state-imposed) Tells you who can lift it and how much testing that takes
Affected area or address ranges Which streets or connections are covered Compare with your building’s address; a neighboring block may not be included
Number of connections How large the area is Small numbers usually mean a local repair
Reason Loss of pressure, line break, repair, positive sample A precautionary reason is not a finding of bacteria; an E. coli result is
Effective date When it began Discard ice and drinks made after this time
What to do Boil for one minute, or use bottled water, and for which uses Post it for everyone in the building
Contact The system’s phone number Call with questions about your address
Release A separate notice when it ends Start the building’s flushing and reset steps

JXN Water’s notices give a date, a street name, address ranges in brackets and “approximately” a number of connections, for example “This notice affects approximately 18 connection(s) in our drinking water system.” MSDH’s notice pages give the system, county, affected area, the reason and a checklist, and move the notice to a released list when it ends.

The federal rules behind a notice

Two EPA rules sit under every Mississippi notice: the Public Notification Rule, which sets how fast people must be told, and the Revised Total Coliform Rule, which sets how systems test for bacteria. MSDH enforces both in Mississippi as the state’s primacy agency; the Jackson court order notes that MSDH “has primary responsibility for the implementation and enforcement of the public water supply program in the State of Mississippi.”

The Public Notification Rule: 24 hours for Tier 1

EPA’s Public Notification Rule page, updated June 3, 2026, sets three tiers. For Tier 1: “Any time a situation occurs where there is the potential for human health to be immediately impacted, water suppliers have 24 hours to notify people who may drink the water about the situation.” Tier 2 notices are due “as soon as possible, but within 30 days,” and Tier 3 within a year.

EPA’s quick reference guide lists the Tier 1 situations, including:

  • A distribution system sample violation “when fecal coliform or E. coli are present,” or a failure to test for them after a positive total coliform sample.
  • A nitrate or nitrite maximum contaminant level violation.
  • “Waterborne disease outbreak or other waterborne emergency.”
  • Detection of E. coli, enterococci or coliphage in a groundwater source sample.
  • “Other violations or situations determined by the primacy agency.”

The guide adds two points that matter to building owners. Notices “must be provided to persons served (not just billing customers),” and a posted notice “must remain in place for as long as the violation or situation persists, but in no case for less than seven days.”

What every notice must contain

EPA lists 10 required elements in a public notice, including a description of the situation, when it occurred, potential health effects, the population at risk, “whether alternate water supplies need to be used,” what the system is doing about it, actions consumers can take, “when the system expects a resolution to the problem,” and how to contact the system. If a notice you receive lacks these, call the system on the number it gives.

The Revised Total Coliform Rule: find and fix

EPA’s Revised Total Coliform Rule page explains why the tests look for coliform bacteria. “Total coliforms are a group of related bacteria that are (with few exceptions) not harmful to humans,” but “EPA considers total coliforms a useful indicator of other pathogens for drinking water” and uses them “to determine the adequacy of water treatment and the integrity of the distribution system.” The rule has applied to all public water systems since April 1, 2016.

EPA’s quick reference guide to the rule describes a “find and fix” approach:

  1. Routine samples are taken on a written sample siting plan and tested by a state certified laboratory.
  2. Any total coliform positive sample must be tested for E. coli.
  3. Within 24 hours of learning of a positive routine sample, the system collects at least three repeat samples: one at the same tap, one within five service connections upstream and one within five downstream.
  4. An E. coli positive result must be reported to the state “by the end of the day that the PWS is notified.”
  5. Assessments. Too many positives trigger a Level 1 assessment by the system; an E. coli violation triggers a Level 2 assessment by the state or a state-approved entity. Each must be submitted within 30 days, and sanitary defects found must be corrected.

A coliform result is not always a boil notice

Not every coliform finding leads to boiling. EPA’s public notification guide includes a model notice for a month in which “7 percent of our samples tested positive” for total coliform against a 5 percent standard. That model notice tells customers “You do not need to boil your water or take other corrective actions,” explains that “coliform bacteria are generally not harmful themselves” but are “used as an indicator that other, potentially-harmful, bacteria may be present,” and reports that follow-up samples found no fecal coliform or E. coli. EPA’s rule page draws the same line: a positive for fecal coliform or E. coli “can signify an acute MCL violation, which necessitates rapid state and public notification,” and “at times, an acute violation due to the presence of fecal coliform or E. coli may result in a ‘boil water’ notice.” In short, total coliform alone starts an investigation; E. coli, or a reason to think the pipes are open to contamination, is what usually starts a boil notice.

When E. coli becomes a violation

The guide’s table shows when E. coli becomes a violation: an E. coli positive routine sample followed by a total coliform positive, E. coli positive or missing repeat sample, or a total coliform positive routine sample followed by an E. coli positive repeat. In Mississippi, an E. coli result is the first trigger on MSDH’s list for a state-imposed notice.

What it takes to lift a boil water notice in Mississippi

A notice is lifted when the cause is fixed and laboratory samples come back clear. MSDH’s 2016 guidelines set out the sequence for a pressure loss, and the number of samples scales with the number of connections affected.

The sequence after a pressure loss

The guidelines say: “pressure must be restored and the distribution system flushed. After flushing, check to insure that there is adequate chlorine residual throughout the distribution system. The Bureau of Public Water Supply typically recommends a free chlorine residual of 0.5 mg/l at the ends of your distribution system. When satisfied that system pressure will be maintained and there is adequate chlorine residual, begin sampling.”

For a notice caused by positive coliform samples rather than pressure loss, the system “should determine the source of contamination and whether the disinfection treatment process is working properly,” confirm chlorine residual, and then sample the affected area, or sites “representing the entire water system” if the whole system is under notice.

How many samples

The guidelines include a chart of samples per round by connections affected. A notice on one street needs only a few samples; a whole-system notice needs well over a hundred.

Samples per round by connections affected (MSDH guidelines, 2016) Samples per round, by connections affected 1 to 1002 101 to 3003 301 to 5004 901 to 1,1007 1,601 to 2,20010 2,801 to 4,30015 8,301 to 11,00030 32,001 to 43,000100 43,001 to 73,000120 73,001 to 107,000150 Purple: the band for a system of about 71,000 connections, the size EPA gives for Jackson's.
Source: MSDH, Guidelines for Issuing a Boil-Water Notice, revised December 1, 2016, sampling requirements chart (selected bands shown; the chart notes that equivalent connections and population served are considered for systems with a large ratio of population to connections). Connection count for Jackson from EPA's Jackson, MS drinking water page. Both checked November 22, 2026.

One round or two

The guidelines are specific: “One (1) round of clear samples is required to release a self-imposed precautionary Boil-Water Alert, but the system may choose to collect two (2) rounds.” For a state-imposed notice, the Bureau “will give explicit instructions on how many samples are required and where to collect them,” and “two (2) consecutive rounds of clear samples are required.” The rounds “do not have to be collected on consecutive days as long as two (2) consecutive rounds of clear samples are obtained.”

The laboratory step

Samples go to the laboratory on MSDH’s form 425 “with ‘Boil-Water Alert’ checked as reason for testing,” with total and free chlorine residuals recorded. MSDH’s private well page says it “normally takes approximately 24 hours for the Public Health Laboratory to analyze a bacteriological sample once it reaches the laboratory.” The 2016 guidelines list days and hours when county health departments and the Public Health Laboratory accept samples, with weekend submissions only by prior approval, and note that the schedule changes in holiday weeks.

Who announces the release

“If the Boil-Water Alert was issued by the Bureau of Public Water Supply, only the Bureau of Public Water Supply can release the alert.” The guidelines’ sample release says that tests performed by the named laboratory “indicate the water is now safe to drink.” For a precautionary notice, the water system announces the release; JXN Water’s page says “residents will be notified immediately when the advisory is lifted.”

How long a boil water notice lasts

No rule sets a fixed length. The steps above set a practical minimum: the repair, flushing and a chlorine check, then at least one round of samples and roughly a day in the laboratory. A state-imposed notice needs two clear rounds, so it lasts longer, and a notice that keeps finding positives lasts until the cause is found and fixed.

From pressure loss to release: the steps of a precautionary notice The steps of a precautionary notice, in order 1. Pressure lostat a break or repair 2. Notice issuedto people served 3. Repair made,pressure restored 4. Lines flushed,chlorine checked 5. Samples taken(count by chart) 6. Laboratory,about 24 hours 7. Clear round(s):1 self, 2 state 8. Released;buildings flush A positive sample sends the process back to step 4 or to a search for the cause.
Source: steps from MSDH, Guidelines for Issuing a Boil-Water Notice (revised December 1, 2016); laboratory time from MSDH's private well disinfection page; checked November 22, 2026. Diagram for illustration; actual durations vary.

Example (fictional). A main breaks on a residential street on a Monday morning, and 40 connections lose pressure. The water system issues a precautionary notice that afternoon. Crews repair the main overnight, restore pressure, flush the line and confirm free chlorine at the end of the section on Tuesday morning. Under the 2016 chart, 40 connections need 2 samples per round. The samples reach the laboratory Tuesday, results come back clear on Wednesday, and the system releases the notice Wednesday afternoon. Had a sample come back positive, the system would have flushed again, checked chlorine and resampled, and the notice would have run several days longer.

What Jackson’s reports show about length

JXN Water’s notices are small and local. The ITPM’s report for the quarter ended December 31, 2025, posted by EPA, says the find-and-fix work on legacy leaks, valves and hydrants “continue[s] to require issuing many precautionary BWN each month.” It reports figures in two places: its notice section counts 112 notices in the quarter averaging 42 connections for 3.6 days, while its summary counts 89 averaging 31 connections for 3.9 days. Either way, the typical Jackson repair notice in that quarter covered a few dozen connections for three to four days. The report also says “there were no city-wide precautionary boil-water notices issued during the reporting period.”

A system-wide example: July to September 2022

A whole-system notice is different in scale. The Interim Stipulated Order in United States v. City of Jackson recites that “on July 29, 2022, MSDH issued a boil-water notice for the System,” that flooding in late August left most of “the approximately 160,000 persons served” without running water, and that “the July 29, 2022, boil-water notice remained in effect until September 15, 2022.” That was a state-issued notice on a system EPA now describes as having “more than 71,000 water connections,” a size that falls in the 120-sample band of MSDH’s chart for each round. More on how the court order changed the system’s management is in Jackson’s water system in 2026.

What a building owner should do while a notice is in effect

A building owner is often the only person who can tell tenants, guests or staff that a notice exists. EPA’s rule says notices must reach “persons served (not just billing customers),” and EPA’s standard distribution language asks recipients to share a notice with people “in apartments, nursing homes, schools, and businesses,” for example “by posting this notice in a public place.” In an apartment building, a hotel or an office, that usually means the owner or manager.

First hour

  1. Confirm the notice applies to your address. Compare the streets or address ranges on the notice with your building. JXN Water lists address ranges for each notice.
  2. Tell everyone in the building. Post the notice at entrances, in elevators, in laundry rooms and at break room sinks. Use your tenant or guest messaging if you have it.
  3. Shut off what people drink from without thinking. Drinking fountains, bottle fillers, coffee brewers, and the water and ice dispensers on refrigerators. The CDC says, “During any type of drinking water advisory, do not drink or use water from appliances connected to your water line.”
  4. Stop ice production. Turn off ice machines and discard ice made since the notice began. MSDH’s 2016 notice template warns: “freezing will not necessarily kill harmful bacteria.”

Filters and treatment equipment

A point-of-use filter does not replace boiling. The CDC says: “Boil your tap water even if you filter it,” including water that “has been through a home water filter or a pitcher that filters water.” Leave UV units and other equipment running as designed, but do not treat them as a substitute for the notice. Make a list of every filter, softener, storage tank and water heater that took in water during the notice; you will need it when the notice ends. Our article on NSF/ANSI filter certifications explains why most filters are not certified for germs.

What stays usable

The CDC says that “in many cases, you can use tap water and soap to wash your hands during a boil water advisory,” that people should be “careful not to swallow any water when bathing or showering,” and that “dishwashers are generally safe to use if they have a sanitizing cycle or reach a final rinse temperature of at least 150°F (66°C).” Food businesses follow the health department’s instructions; our article on running a restaurant during a boil water notice covers that case. Household steps are in the boil water notice checklist.

After the notice is lifted: bringing a building back

When a notice is lifted, the water in the street is cleared, but the water already inside your building’s pipes, tanks and appliances is not. MSDH’s 2016 release template tells customers to flush their plumbing and reset what took in water during the notice, and its current notices repeat the core steps.

MSDH’s release steps

The 2016 guidelines’ release template says:

  • “Flush faucets for a total of ten (10) minutes to introduce system water throughout house plumbing.” For example, one faucet for 10 minutes, two faucets for 5 minutes each, three faucets for 3 to 4 minutes each.
  • “Flush any faucet a minimum of two (2) minutes to ensure clearing of the line serving the faucet.”
  • “Discard any drinks, ice, food, etc, made during the Boil-Water Alert.”
  • “Rewash any food or drink contact items (knives, forks, plates, etc.) with ‘cleared’ system water.”
  • “Check water filters (in faucets, refrigerators and elsewhere) and replace if necessary.”
  • “Run dishwasher through a cycle or two before washing dishes.”

The Town of Utica notice from November 2026 gives the same steps in shorter form under “When the Notice Is Released.”

Scaling the steps to a larger building

A house has a few faucets near the meter. A hotel or apartment building has risers, long branches, storage and equipment, so the same steps take a plan. The table sets out each part of a building and the step that applies, with its basis.

Part of the building Step after release Basis
Cold water taps Flush, working outward from the point where water enters the building, at least 2 minutes per faucet MSDH release steps; checklist tool
Drinking fountains and bottle fillers Flush, then return to service; replace any filter cartridge that took in water MSDH (check and replace filters)
Ice machines and beverage equipment Discard ice, then flush and sanitize following the manufacturer’s instructions MSDH (discard ice); checklist tool
Refrigerator water and ice dispensers Discard ice, flush the line, replace the filter if needed MSDH (check filters)
Point-of-use filters and RO units Replace cartridges that took in water during the notice MSDH; checklist tool
Water heaters and storage tanks Drain and refill if the utility or the manufacturer advises it Checklist tool
Dishwashers Run empty through a cycle or two MSDH release steps
Records Note what was flushed, replaced and when Checklist tool

Example (fictional). A 60-unit apartment building gets word that a three-day precautionary notice on its street has been lifted. The manager posts the release in the lobby and on the tenant portal with MSDH’s flushing guidance for each unit. Maintenance then flushes the common areas, starting with the hose bib nearest the meter and working up the risers to the top-floor laundry room. They discard the ice in the community room machine, sanitize it following its manual, and change the cartridges on the two lobby bottle fillers. The entries go into the building’s maintenance log with dates and part numbers.

Why the log matters

A dated log answers the questions that come later: which cartridges were changed, when the ice machine was cleaned, which floors were flushed. The monitoring and service plan Maredes offers for systems it designs keeps a maintenance log of this kind, and the filter maintenance log is a free printable version for any building.

Common questions about boil water notices

These short answers come from the sources above. For a question about your own address, call the water system named on the notice.

Why is my street under a notice but not the next one?

Notices follow the part of the pipe network that lost pressure, not neighborhood lines. JXN Water’s notices list address ranges street by street, so one block can be included while the next is not. Check the exact range against your address, and call the system if your building sits at the edge of one.

Can a notice be lifted the same day it starts?

Rarely. Under MSDH’s 2016 guidelines, sampling begins only after pressure is restored, the lines are flushed and chlorine residual is confirmed, and MSDH says its laboratory normally needs about 24 hours to analyze a bacteriological sample after it arrives. That puts a practical floor of a day or more under most notices.

Is it safe to shower or wash hands?

The CDC says that in many cases you can wash hands with tap water and soap during a boil water advisory, and that people should be careful not to swallow water when bathing or showering. Follow the notice you received if it says otherwise.

Does a notice mean someone got sick?

Not necessarily. JXN Water describes its notices as precautionary and the result of repair work, and MSDH’s Utica notice gave “loss of pressure caused by a line break” as the reason. A notice that cites an E. coli result or an outbreak will say so.

Who do I call?

For a notice from your water system, call the number on the notice; JXN Water’s line is 601-500-5200. For questions about state-imposed notices, MSDH lists its Bureau of Public Water Supply at 601-576-7518.

Planning for the next notice

Repair notices are a normal part of a water system’s maintenance, and buildings that plan for them recover faster. A short written plan, kept with the building’s emergency information, covers most of what matters.

A one-page plan

  1. Know both notice sources. Bookmark JXN Water’s notice page if you are in Jackson, and MSDH’s water safety notices anywhere in Mississippi.
  2. Name who posts notices to tenants, guests or staff, and where.
  3. List every point people drink from: taps, fountains, bottle fillers, ice machines, coffee and beverage equipment, refrigerator dispensers.
  4. List every piece of treatment equipment with its cartridge part numbers, so replacements are on hand.
  5. Write the flushing route from the meter outward, floor by floor.
  6. Keep bottled water for the first hours of a notice.
  7. Log each notice: dates, what was shut off, what was flushed and replaced.

Where Maredes fits

Maredes is a Jackson, Mississippi company that designs compact water treatment and reuse systems for one building at a time. It does not issue or lift notices, give health advice or test water itself. When it specifies drinking water systems for a building, the specification lists each point of use and the cartridges to replace after a notice, so the recovery steps above are written down before they are needed. The Jackson and Mississippi page keeps regional facts and links in one place. To plan this for your building, request a water review. More on water rules in Mississippi is in standards and rules.

Have a building in mind?

If this article describes a question about your home, property or business, tell us about the building. A project starts with a water review and a written summary of what we found.